Cold forming mill / LW1600 Cold Forming Mill
- Ref Price:
-
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
The introduction of coldrollforming section mill
The rolling plate in certainwidth is unfolded and leveled. Then, they are sent in to the forming machine.The steel plate is bent to be the needed form in the cold conditions by usingthe roller.
According to the differentproducts, the cold forming steel mills are divided into square pipe mill, steelsheet pile mill, and other kinds of mills.
Square pipe mill mainly producesthe square and rectangular pipes, all kinds of which in the range of roller productionspecifications can be achieved by using direct forming tectonics and theassisted high frequency welding machine.
Steel sheet pile mill mainlyproduces the steel sheet pile by adopting piecewise arc flexible formingtechnology. Steel sheet pipe mill in our company has reached the top level allaround the word.
Other models can produce U-steel,Hat shape steel, carriage U-steel, C-purlin and other steels by changing the roller
Pipe diameter :Square □120×120～□400×400mm
Rectangular □100×130～□300×500mm
Wall thickness: 3.0～12.7 mm
Strip width : 480～1600mm
Forming speed : 0～15m/min
Power of high-frequency unit: 800kW
Main motor: model (DC) power 200kw×2 250kW speed 500/1600rpm
Strip width : 480～1600mm
Forming speed : 0～15m/min
Cut-to-length accuracy: ± 3 mm (electronic flying saw)
Overall dimension :length 150,000mm
- Q: A roll forming machine, rolling out of the length is always not up to a fixed size, not too small, that is, more than that, what is the cause?
- Yes, the width of the bearing plate can be a deviation from the length.
- Q: What is rolling forming processing?
- Ironing the surface of the workpiece with a raised micro wave crest to fill the concave micro troughs, thus changing the distribution of the peaks on the surface, and obtaining smaller surface roughness values.
- Q: Improvement in rolling forming process
- It is difficult to control the rolling process and can cause waste easily.
- Q: Introduction of roll forming process
- With the progress of technology and the development of production, more and more attention has been paid to the roll forming process.
- Q: What kind of material and what heat treatment are used for pressing roller (molding, feeding, cutting force, heavy load, heavy load) of sheet steel rolling machine?
- Use 40Cr or 20Cr, Cr12.Cr12MoV, quenching and tempering treatment, think of hardness, high point, carburizing, nitriding, and consider adding lubrication device to extend its service life
- Q: What is the surface rolling forming machine process?
- Due to the rolling surface of metal plastic deformation, so that the surface microstructure of cold hardening and grain refinement, forming a dense fibrous, and the formation of residual stress, hardness and strength, so as to improve the surface wear resistance, corrosion resistance and compliance.
- Q: Process mould for rolling forming process
- A movable wire plate, made of the same fixed wire plate, for relative reciprocating motion. Roll forming is the design of different structures on the plate rolling on the workpiece. Roll out all kinds of thread, convex ring, knurling, end chamfering, groove with different width and thickness as well as other required shapes.
- Q: Material and equipment for roll forming process
- The most common type of roll forming is reciprocating flat wire twisting machine. Therefore, for the manufacturers of cold heading machines and screw rolling mills, the design of rolling dies is only a matter of design.
Send your message to us
Cold forming mill / LW1600 Cold Forming Mill
- Ref Price:
-
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
