CD₁Electric Hoist,Small-Sized and Light Lifting Equipment
- Loading Port:
- China main port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 pc
- Supply Capability:
- 200 pc/month
- Option:
- Technical Data Technical Data Technical Data
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Item specifice
Main application and scope
Model CD, MD wire rope Electric Hoist is a small-sized and light lifting equipment, which can be mounted on single beam、bridge、gantry and jib crane. With slight modification, it also can serve as winch. Thus, it is widely used in factories、mines、harbors、warehouse、cargo storage areas and shops.It is essential in raising working efficiency and it also can improve working conditions.
Model CD Electric Hoist has only one normal speed, which can satisfy normal supplication. MD Wire rope Electric Hoist is provided two speeds: normal speed and low speed. At a low speed, it can do precise loading and unloading、mounding of sand box、maintenance of machine tools and etc. Thus, MD Wire rope Electric Hoist is more widely used than Model CD.
To meet the needs of lifting heavier cargo, our factory manufactures WH20T and WH32T Electric hoist.
The difference between CD and MD
1.The lifting speed of the CD model is constant speed, which can fit the general requirements.
2.MD model has two lifting speeds - normal speed and slow speed.
3.When it slow work, can meet the requirements of precision loading and unloading , sand box mold, machine repair and other fine operations. Therefore, the use of MD electric hoist more widely than the CD electric hoist.
4.MD model price is more expensive than CD model.
Safety and working conditions
The working environment temperature of this product is between -20 and +40 degrees centigrade. It is not suitable for the workplace where there is explosion danger, fire danger, acid or other corrosive gas and relative humidity is greater than 85%. Not for manned use. The operation shall be carried out in strict accordance with GB6067-1985 "crane safety regulations".For use in open spaces, protective devices shall be provided against moisture.
The product load sustained rate of FC25%, starting times 120 / hour.
The main structure and working principle of Model CD/MD electric hoist
Model CD/MD electric hoist is mainly composed of three parts: lifting mechanism, running mechanism (stationary type) and electrical control device
Model CD/MD electric hoist appearance structure
1. soft cable introduction frame
2. electric control box
3. trolley
4. reducer
5. electric motor
6. lifting hook
7. lifting motor
8. fire stopper
9. limited rod
10.rope guide
11.stop block
12.hoisting reducer
13.roll device Figure 1a: CD Model electric hoist 0.5t H=6m-12m
14.trolley equalizer
15.two wheel trolley
Installation method
First, you need to install the chain box first.
Second, connect the power cord.
When connecting the power cord, must be cut off the power in advance.The ground line should be well grounded at same time, otherwise the operator may feel electric shock when touching any part of the gourd or chain.
Third, the load chain of Lubricated ring chain electric hoist
The lubrication degree of chain is an important factor affecting the service life of load chain.Timely and effective lubrication of load chain can guarantee the effective service life of the chain.
Fourth, check the chain alignment
For multi-chain ring chain electric hoist, should make sure that the hook rack is not flipped.If flipped, return it to normal and ensure that the chain is arranged in line.Do not hang the load on the chain's twisted gourd.
Finally, check the working voltage
Because of the link chain electric hoist out of the factory, they are made according to the user specified voltage or high voltage equipment (only for dual voltage), such as 230/460 v, the operator to check and confirm whether meet the requirements of power supply voltage.If not, please refer to the instructions to meet the required working voltage requirements.
CD1 MD1 | ||||||||||
Lifting capacity(t) | 0.25 | 0.5 | 1 | 2 | 3 | 5 | 10 | 16 | ||
Hoisting height(m) | 3/6/9 | 6/9/12 | 6/9/12/18/24/30 | 6/9/12/18/24/30 | 6/9/12/18/24/30 | 9/12/18/24/30 | 9/12/18/24/30 | |||
Hoisting speed(m/min) | 8(0.8/8) | 7(0.7/7) | 3.5(0.35/3.5) | |||||||
Traveling speed(m/min) | 20 | 20/30 | 18 | |||||||
Wire rope | Dia (mm) | 3.6 | 4.8 | 7.4 | 11 | 13 | 15 | 17.5 | ||
specification | 6*19 | 6*37 | ||||||||
Track | 10-20b | 16-28b | 20a-32c | 25a-50b | 32b-50b | 32b-63c | ||||
Min. Curvature radius(m) | 0.8 | 1.5 | 1.5/2/3/4 | 2/2.5/3/4 | 2/2.5/3/4 | 2.5/3/4/4.5/6 | 3.5/4/6/7.5/9 | 3.5/4/6/8/11 | ||
Type | ZD₁12-4 | ZD₁21-4 | ZD₁22-4 | ZD₁31-4 | ZD₁32-4 | ZD₁41-4 | ZD₁51-4
| |||
ZDS₁0.2/0.8 | ZDS₁0.2/1.5 | ZDS₁0.4/3.0 | ZDS₁0.4/4.5 | ZDS₁0.8/7.5 | ZDS₁1.5/13
| |||||
0.4 | 0.8(0.2/0.8) | 0.2(0.2/1.5) | 3.0(0.4/3.0) | 4.5(0.4/4.5) | 7.5(0.8/7.5) | 13(1.5/13) | ||||
1380 | 1400 | |||||||||
1.25 | 2.4(0.72/2.4) | 4.3(0.72/4.3) | 7.6(1.25/7.0) | 11(1.25/11) | 18(2.4/18) | 30(5.2/30) | ||||
Type | ZDY₁10-4 | ZDY₁11-4 | ZDY₁12-4 | ZDY₁21-4 | ||||||
Power(RW) | 0.06 | 0.2 | 0.4 | 0.8 | ||||||
Rotation speed(r/min) | 1400 | 1380 | 1380 | 1380 | ||||||
Current (A) | 0.3 | 0.72 | 1.25 | 2.4 | ||||||
No. Of connecting | 120 | |||||||||
Duty classification | Intermediate FC=25% | |||||||||
Power source | Three-phase AC 380 V50Hz | |||||||||
L | 391 | 616/688/760 | 758/856/954/1150/1346/1542 | 820/920/1020/1220/1420/1620 | 932/1038/1138/1327/1533/1738 | 1047/1157/1257/1467/167//1887 | 1602/1783/2145/2507/2869/1872/2092/2532/2952/3387 | |||
L1 | Basic Dimensions (mm) | 78 | 274/364/418 | 345/443/541/737/933/1129 | 352/452/552/752/952/1152 | 380/483/586/792/998/1204 | 415/525/625/835/1045/1255 | 875/1056/1418/1780/2142/1136/1356/1796/2216/2651 | ||
216 | 125 | 158 | 187 | 229 | 267 | 301 | ||||
L3 | 318/390/462 | 401/499/597/793/989/1185 | 418/518/618/818/1018/1218 | 448/551/654/860/1060/1272 | 485/606/695/905/1115/1325 | 949/1130/1492/1854/2216/1210/1430/1870/2290/2725 | ||||
L4 | 190 | 196 | 240 | 264 | 320 | 376 | ||||
B | 279-315 | 884 | 930 | 1055 | ||||||
H | 423 | 650 | 667/767 | 840/950 | 954/1058 | 1120/1183 | 1350 2100 | |||
d | 17 | 20 | 25 | 25(31) | 25(37) | |||||
b | 185 | 185/270/470/660/860 | 205/280/480/680/880 | 205/320/530/730/940 | 228/340/550/760/920/ | 490/670/1030/1395/1760/860/1080/1520/1940/2375 | ||||
CD1 | Crane weight (KG) | 44/45/46/ | 121/125/130 | 137/145/172/188/204/220 | 221/232/285/309/332/353 | 281/297/354/390/420/451 | 437/495/597/646/686/726 | 1048/1098/1209/1301/1411/1130/1183/1286/1463/1563 | ||
/MD1 | 138/142/147 | 164/174/199/215/231/247 | 256/267/320/344/361/388 | 311/327/384/420/450/481 | 508/532/654/703/743/783 | 1104/1154/1265/1366/1467/1220/1273/1376/1553/1653 | ||||
CD1(FIXED) | 30/31/32 | 89/94/99 | 105/112/120/135159/165 | 166/179/186/209/229/249 | 222/236/250/284/312/340 | 377/400/415/456/493/529 | 795/841/943/1035/1127/850/903/1006/1183/1283 | |||
MD1(FIXED) | 106/111/116 | 132/140/147/162/177/192 | 201/211/221/244/264/284 | 252/266/280/314/342/370 | 430/457/472/513/549/586 | 851/897/999/1091/1183/949/997/1090/1273/1373 |
- Q:they put a hole in my sidewall of my rear tire putting my truck on the lift ..the driver did not go in strait and the tire missed the ramp and punched a hole in the sidewall.. there is a pin and a cotter pin on the left side of the hoist...
- I work in the automotive business and have for several years. chances are that they didn't do it, if they had and they were a reputable repair shop, they would have let you know what the problem was and then fixed the problem. I know you're not supposed to plug or patch a sidewall hole, but it can be done successfully and safely. if it was a drive-on lift with two platforms for the vehicle to drive on, if he missed the ramp then there would be a few more serious problems than just a puctured tire. I honestly don't think that the repair shop caused the problem.
- Q:I just need help, i still have to interpret it and read all of whatever its in. Your not doing it for me so relax! If you know where any of these are or in any show or commercial of book or WHATEVER just like tell me?Pyrrhic VictoryDelphic OracleFlash in the PanOver a BarrelDon QuixoteDoublespeakBenedict ArnoldMurphy’s LawHoist with one’s own petard
- I think you can type each one in your Google or Yahoo search and each one should have a site to refer to that will give you the info you need.
- Q:Electric gourd security check specification, how many tons below need security check
- A tower crane that is greater than or equal to 40t m, or a loading bridge that is greater than or equal to 300t/h, and elevating a crane that is greater than or equal to 2m. The number of layers is greater than or equal to the mechanical formula of the two layers Parking equipment. " The weight of the electric gourd may be less than 3 tons. If the rated weight of the equipment is indeed less than the relevant parameters in the above definition, the crane machine will not be incorporated into the government
- Q:chain link up to this turning device, slaves would grab hold of handles and push clockwise, then the chain would begin to coil around it's base or where ever, the other end of the chain would be linked to a cage or door and as the chain coiled the cage or door would rise. What the devices name?
- a winch or hoist for raising a portcullis. winch hoist windlass capstan
- Q:It has been stuck in my head for the longest time.
- The theme song is called: He's a Pirate
- Q:I have this question in Mech engineering. If anyone could tell me HOW to answer it that would be grand. I don't want the answer I already have that, but if someone could tell me how to get the answer that would be great. ThanksQA load of mass 8 tonne is to be raised with a uniform acceleration of 1.1 m/s^2 by means of a light cable passing over a hoist drum of 2 m diameter. The drum has a mass of 1 tonne an a radius of gyration of 750 mm. Find the torque required at the drum if friction is neglected.A(87.8 KN-M)Once again it is the working I need not the answer. Thanks people
- The load is not just raising, it is accelerating also. You can add the uniform acceleration of 1.1 m/s^2 to acceleration of gravity (9.81 m/s^2). So a = 9.81 + 1.1 = 10.91 m/s^2. Force on cable = ma = 10.91m/s^2 x 8,000 kg = 87,280N Radius of drum = d/2 = 1m Torque from just the load = 87.28kN x 1m = 87.28kN-m Now find torque to accelerate the 1 tonne hoist drum T = Iα I = k^2 x m = (1000) x (0.750)^2 = 562.5 Since the drum radius = 1m, tangential acceleration at surface = 1.1 m/s^2 and α = 1.1/1 = 1.1 rad/sec T = 562.5 x 1.1 = 618.7 N-m = 0.619 kN-m Total torque = 87.28kN-m + 0.62 kN-m = 87.9kN-m Well, that's close. Go thru the numbers again to check; if you use g = 9.8 you will probably get the exact same answer. Hope this helps. Let me know if you need clarification. Bill
- Q:An electric hoist is being used to lift a beam (see figure). The diameter of the drum on the hoist is x = 14 inches, and the beam must be raised y = 2.9 feet. Find the number of degrees through which the drum must rotate.
- 2.9feet = 33 inches i.e 33inches to be wound on 14inch drum 1 revolution = 360 degrees =pi x diameter = 43.98inches Simple proportion: 43.98 = 360 33 = ? 270 degrees
- Q:Why do electric gourds use a broken fire limiter instead of a travel switch
- Electric gourds, which are strictly controlled by lifting equipment, are only the coil that controls the contactor, if the contactor itself is a problem. The travel switch is not protective. The fire limiter is mechanical protection and the connection is correct. It can protect.
- Q:limits of 2 of its components, For the amount of weight being lifted, the probability that the upper attachment hook will fail is 0.20. The probability that the lower hook will fail is 0.10. What is the probability that the hoisting job will be successfully completed? I got 70%. Just seems to simple to be correct. Thanks
- assuming independence of failures, P(successful) = P(neither fail) = 0.8*0.9 = 0.72 ------
- Q:Three tons of electric gourd, span 10 meters need what type of steel to be girder
- G. The hook should be flexible in horizontal and vertical direction. The pulley should be flexible. I. Steel wire rope should not be clearly cracked, and lined up on the drum, no loose pulley groove, twist, buckle, etc., and the lubrication is good. There is no abnormality in the crane. K. electric hoist working environment temperature is 25 ~ + 40 ℃ L. electric hoist is not applicable to full of corrosive gas or relative humidity is more than 85% of the place, not a substitute for explosion-proof hoist, unfavorable lifting molten metal or toxic, flammable and explosive. (2) the electric gourd shall not be suspended from the side, and shall be prohibited from overloading.
1. Manufacturer Overview |
|
---|---|
Location | |
Year Established | |
Annual Output Value | |
Main Markets | |
Company Certifications |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | |
No.of Employees in Trade Department | |
Language Spoken: | |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
CD₁Electric Hoist,Small-Sized and Light Lifting Equipment
- Loading Port:
- China main port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 pc
- Supply Capability:
- 200 pc/month
- Option:
- Technical Data Technical Data Technical Data
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Related keywords