Butterfly Valve Without Pin Ductile Iron DN430

Ref Price:
Loading Port:
Payment Terms:
Min Order Qty:
5 set
Supply Capability:
50000 set/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Centerline structure,pinless double half shaft design.
Disc has two-way bearing, no installation direction requirements.
Non-backed replaceable seat with good performance and a longer working life.
Square and short neck for lable use and cost saving.
Easy installation, no need flange gasket.


Design standardAPI609/EN593
End flangeDINPN10/PN16, BS4504PN10/PN16, ANSI class125#/class150#
Face to faceAPI609/EN558-1
Top flangeISO5211
BodyDuctile iron/Cast iron
DiscDuctile iron/CF8/CF8M/C95400/C95500
ActuatorBare shaft/Lever/Gearbox and handwheel
PinWith out pin
Suitable mediumWater/Seawater/Sewage/Air/Foodstuff/Oil



Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:What does valve qz45x - 10q mean?
Crown valve pressWhat does Q stand for? I'm not sure. It's probably made of ductile iron"Z" means "gate valve"4 represents flange connection5 represents the dark bar (1 represents the Ming pole)X stands for rubber seal and soft seal10q stands for 10 pressure
Q:What is the difference between an elastic gate valve and a rigid gate?
Brief introduction: the valve gate valve is a gate opening and closing parts, RAM direction of motion perpendicular to the direction of the fluid, valve can only be fully open and fully closed, can not be adjusted and the throttle. Gate has two sealing surface, the most commonly used mode gate valve of the two sealing surface to form a wedge, wedge angle with valve parameters vary, usually 50, medium temperature is not high when 2 degrees 52'.Wedge gate valve can be made into a whole, called the rigid gate; can also be made to produce micro deformation of ram, in order to improve its process of deviation, make up the sealing surface angle in the process, the gate is called the flexible gate.
Q:Which is more expensive, bronze gate valve or brass gate valve?
The advantage of casting method is more obvious. The casting of stainless steel is much more difficult than that of brass.
Q:Why does the centrifugal pump start and stop in the case of closing the gate valve?
Centrifugal pump to close the gate valve in the case of the start: the centrifugal pump power increases with its flow rate, when the flow is zero (valve closed), the minimum power to operate. Start the valve off from the angle of the motor. If the valve is started, the motor itself to start the current is larger, coupled with the power of the pump is also large, easy to cause the motor over-current trip, serious will burn the motor.
Q:Function of signal butterfly valve and gate valve
The signal butterfly valve applies to petroleum, chemical, food, medicine, papermaking, water and electricity, ships, water supply and drainage, smelting, energy and other system pipelines. Available in a variety of corrosive, non corrosive gases, liquids, semi fluids, and solid powders.
Q:What type of flange does it fit with the gate valve?
According to the welding plate flange, flange material selection of piping material.
Q:Notes on flat gate valves
Use, maintenance, maintenance and precautions1. valve before leaving the factory have made strength and sealing test, the use of all connections should maintain the initial state.2. this series of valve operating handwheel is marked with open and close rotary direction, and the upper part of rod is equipped with open and close height gauge for regulating indication.3. when the valve and pipeline welding, the valve should be opened, appropriate to protect the neck with moisture, minimize heat conduction, to prevent damage to the sealing packing parts.4. when the valve is closed, the lever shall not be used. When the gate is closed to the top, the handwheel shall be turned 1/2 so that the gate is in a floating state.5. in the use of the valve should be regularly to the valve cap injection grease joint into the quantitative grease.6., the valve in use, such as vulnerable parts and leakage, should be replaced in time.7., the valve in the overhaul process, the cavity should be cleaned, the assembly should be added to the transmission parts of grease.8. valve storage during the shutdown, the gate should be in the closed position, long-term storage should be placed in ventilated dry place, regular inspection and maintenance.
Q:What is the standard length of GB steel gate valve?
1, product standardsGeneral purpose valves, flanged connections, iron gate valves, GB/T 12232-2005General requirements for steel valves GB/T 12224-2005"Steel flat gate valves for pipelines" JB/T 5298-91Inspection and test of valves. JB/T 9092-1999Standard for safety evaluation of drinking water distribution equipment and protective materials GB/T 17219-1998
Q:What is the size and length of the DN80 gate valve? 10 kg and 16 kg, respectively?
Valve structure length standards are PN16, short series for 203mm, long series for 280mm, flange size by PN16.
Q:Gate valve Z41H-16Q generally used for what place?
It is a standard flanged gate valve with engineering pressure 1.6MPa. Generally used in chemical processes, of course, can also be used for municipal and civil engineering. The valve is generally used for cutting occasions fully open or fully closed, is not suitable for flow regulation.

1. Manufacturer Overview

Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range