Art no. HT-TS1006 Ceramic knife set with acrylic stand

Ref Price:
Loading Port:
Guangzhou
Payment Terms:
TT OR LC
Min Order Qty:
500 PCS
Supply Capability:
100000 PCS/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Ceramic knife set with acrylic stand

Set includes:

              6-inch small chef knife,1.8mm

              5-inch carving knife,1.8mm

              3-inch fruit knife,1.6mm

              peeler

              acrylic stand

Blade:zirconia

Handle:ABS+TPR

Packing:with color box

You can choose the handle color you like

Zirconium material keeping 90° hardness just second to diamond which give the ceramic knife its outstanding sharpness and edge retention

Ergonomically shaped ABS + TPR handle in any color  which keep the ceramic knife lightweight and colorful


Primary Competitive Advantages:

Country of Origin         Packaging

Price                     Product Features

Prompt                    DeliveryService

Small Orders Accepted


Main Export Markets:

North America            Central/South America

Western Europe


Maintenance:

Only use plastic or wood cutting board

As with only knife, avoid dropping, throwing or generalmisuse

Avoid using the ceramic knife to cut seeds, bones, frozen foodor other hard product

Not flexible, don't use it to smash garlic, open cans orattempt to bent it in any way

Hand wash only

Do not attempt to sharpen the ceramic knife yourself unless youhave access to sharpener specific to ceramic knives


Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:How long is the control tool?
Do you want to carry a knife with you? The specification of the cutting tool is very long, I will give you the following: with self-locking device, without self-locking device is less than 60 degrees angle. As long as the above 2 belong to the control tool, if you bring a small dagger is only 6 cm long, but with a self-locking device, also belong to the control tool
Q:Woodworking engraving machine commonly used tools which?
Taper ball end cutter, referred to as spherical cone. Is a mixture of spherical cone cone knife and knife, knife cone has the characteristics of it on the one hand, has a very small nose, on the other hand a knife features, can fine carving surface. The cone knife is often used to relief surface carving, engraving, carving and other relief image projection.Taper nose knife, knife cone taper is a mixture of bovine and bovine knife knife, knife cone has the characteristics of it on the one hand, has a small nose, fine carving and milling surface, on the other hand, has the characteristics of cownose knife, so the knife is often used in the nose taper relief surface engraving.Big head knife, in fact, the head of the cone angle larger cone knife. Mainly used for three-dimensional clearance.Drilling tool, mainly used for drilling. When the hole is relatively shallow, you can use a flat knife.
Q:How to maintain cutting tools?
At the scene, I suggest the "management", which are each tool in the toolbox has a fixed position, so that not only can avoid the tool damage, and can greatly improve the production efficiency.The warehouse can be stored in accordance with the warehouse management law.
Q:How to clean the kitchen tool set
Kitchen tools need to be cleaned after use, and then dry.
Q:Turning steel pipe, what is good?
Feed from you for the 0.307 to judge, should not be a tool, but feed selection is too large, normally used coarse feed 0.3 is not small, not to mention the eccentric shaft, suggestions will feed appropriate small try.45# steel is generally used in the case of the YT15 is more suitable, YT5 poor wear resistance, YS8 brittle easy to jump knife. As for the speed depends mainly on the size of the workpiece diameter, if you use the cutting speed to measure, then the general rough car with 60 to 80 meters per minute, fine car with a 80 to 120 meters, the eccentric shaft should be appropriate to reduce the cutting speed.
Q:What is the difference between the choice of the angle of the rough and the fine?
Did not understand your specific meaning, the angle of the lane is not the angle between the axis, the tool can be used to adjust the holder.Should be the angle of the lane itself, that is, the angle of the cutting tool. Rough machining of the general lathe because of large, large force, so the cutting tool should not be too sharp, otherwise easy to break. Fine Lane because the feed is very small, less force than the general blade angle. At the same time, it can prevent the metal filings in the gap between the workpiece and the cutting tool. Therefore, in the selection of turning tools, it looks thick and blunt is generally rough turning.
Q:Tool quenching method
If your tool is used in the daily life of the family, here are some suggestions:1, use your iron tapping tool, a sound and sound hum for a long time, your tool has higher carbon content (carbon content in 5/1000~8/1000). Otherwise, such as sound and sound and soon disappeared, and that the tool is very low carbon content (0.8/1000~2/1000), at this time, you do not need to heat treatment, heat treatment can not be normal because of the material change.2, prepare a ~20Kg can contain water wide mouth containers (according to the size of the opening and the depth of your tool size and determine the length of the container), the water temperature is 35 DEG ~50 DEG (water quenching medium had a lot of good, but you don't necessarily have the water, is the quenching medium, cheap water for heating the tool to prevent serious deformation and excluded) poured into containers (with 20~30mm filled).3, your tool blade (blade in the range of ~40mm) is heated to appear incandescent color (about 820 DEG ~850 DEG, because you don't necessarily have the thermometer, so use color to judge the temperature), quickly after you get ready for the 35 straight down into the water of ~50 DEG C, and immediately on the vertical under water sports (you don't move a tool sideways in the water movement, this is to prevent the deformation) about 4~7 seconds (such as cutting edge thickness is 0.5~2mm (or you) feel the tool vibration disappeared; or listening to the water sound disappeared), presents a tool.4, the tool immediately on the flame (note, not in the fire) to bake at 120 degrees C ~150 C (small splash of water splashed on the tool immediately jump boiling), and then natural cooling can be.
Q:What cutting properties should be provided for the cutting parts
1 high hardness tool material hardness is higher than the hardness of the workpiece material; wear resistance of 2 high wear resistance, is a comprehensive reflection of the tool material mechanical properties, microstructure and chemical properties; 3 sufficient strength and toughness; 4 high heat resistance; thermal physical properties of 5 and good thermal shock resistance 6; good technology and economic performance.
Q:I would like to ask what is the most secure tool features?
Blade resilienceMost of the accidents due to the use of the tool is the occurrence of the user in the process of cutting tools, or blade for a long time in the user can contact the state. Therefore, the blade rebound is a "safety tool" can not be missing function.
Q:What is the relative motion between the tool and the blank?
The linear speed of the gear cutter and the gear blank.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range