Quick Details for Alumina Ceramic Foam Filter for Air and Water Treatment
|Place of Origin:|
PU foam (polyurethane foam)
10 ppi to 60 ppi
Mend structure of crystalloid
Reduce foreign matter
Stable chemical property
Stable purifying efficiency
|polyurethane foam filter:|
|Packaging Details:||carton and pallet, or as customers' requirement|
|Delivery Detail:||30 days after receiving the downpayment|
Alumina ceramic foam filter
The product, adopted good portiforium foam and high purity ceramic , effectively removes non-metal solid mixture from aluminium and aluminium alloy fusant.
Alumina ceramic foam filter
1.even aperture, high porosity, proper sinter
2.high strength of anti-flexing and anti-compression
even aperture, high porosity, proper sinter, high strength of anti-flexing and anti-compression, effective filtering.
It is widely applied to the aluminium fusant filter equipment of continuous casting, half-continuous casting, gravity casting, and low pressure casting.
Ceramic foam filters are different from aperture specifications from 10 to 45ppi, with different sizes and shapes.
Besides the general specification ,we can offer the product according to the customers requirements.
Form A Ceramic foam filter capability
Tortuous intensity in normal temperature
Pressure resistence intensity
in normal temperature
in high temperature
Form B 25ppi capability of typical pouring of ceramic foam filter
Maximum metal volume of pouring
Optimum volume of pouring
Typical capacity of filtering
Welcome to visit our factory~
- Q:Can the ceramic plate filter the hot air?
- Ceramic filter by vacuum suction effect in the ceramic filter plate to cake drying purpose, ceramic filter plate needs cleaning and life, if you discover that the slurry sucking effect is poor or even grout should first consider the three aspects: the two factors of ceramic filtering plate of ceramic filter plate most likely, are fracture and hole plugging: rupture will lead to distortion and poor vacuum cleaning; plugging holes will cause the filter plate suction effect is poor even if grout, ceramic filter plugging hole, can strengthen the appropriate cleaning (such as shortening cleaning cycle, prolong the cleaning time, increase the amount of nitric acid, such as strengthening cleaning etc.) after the effect is still not improved, you should consider the life is approaching should be scrapped and replaced with ceramic filter plate new (replacement plate should not put new or different manufacturers is mounted on the same line, the most OK, complete replacement.).
- Q:What is the reason that ceramic filter does not absorb mineral powder?
- In order to avoid frequent fluctuations in pressure and pressure within a short period of time, a buffer cylinder with a stabilizing effect is provided in the backwash pipe.
- Q:What is the working pressure of the ceramic filter?
- Vacuum pressure or suction is the vacuum of the equipment, the size of the vacuum directly affects the effect of ceramic filter board suction (yield and water content). The vacuum system of ceramic filter consists of vacuum pumps, tanks, distribution device, ceramic filter plate and a connecting pipe is composed of ceramic filter, the vacuum pump is generally 2BV series water circulation pump, the vacuum pump vacuum limit is -0.097MPa, using a vacuum pump for a long time or vacuum system has poor sealing performance may cause a certain degree of vacuum distortion, so the ceramic filter vacuum is generally difficult to achieve in the -0.097MPa, -0.08 ~ 0.097MPa, which indicates that the vacuum degree is good, such as the vacuum degree is not up to -0.07MPa or less, the vacuum system may be an exception.
- Q:What about the leakage of the ceramic filter static and dynamic sealing points?
- When the main shaft is rotated, the filter cake is adsorbed on the surface of the ceramic filter plate and dehydrated by the vacuum generated by the vacuum pump.
- Q:How can I avoid the backwash pressure in the production of ceramic filter?
- The backwashing system of ceramic filter is usually made up of water inlet, water inlet, pressure gauge, water filter and filtered water pressure gauge, and then connected to the inside of ceramic filter. Such as the discovery of ceramic filter recoil pressure became smaller or even no recoil pressure, you can carefully observe the surface of the ceramic filter plate is wet or ceramic filter plate wear without water injection at the discharge point, investigation and the reasons for the following aspects:Is the water inlet pressure or normal?How about the sealing performance of the water filter? Does the filter element need to be replaced?Is the recoil system piping (metal pipe, ceramic filter plate, connecting pipe, etc.) broken, leaking or dripping?Is the distributor valve properly installed and is it worn?Are there any cracks in the ceramic filter plate?Is the pressure gauge broken?The most likely reason is 1, 2, two, the best water should not be too dirty, filter should be replaced regularly. I hope the answer can help you.
- Q:What's the reason for high water content in filtration copper concentrate?
- Can the cleaning of ceramic plate meet the requirement?Such as cleaning of ceramic plate is not up to the requirements, plugging holes will increase the risk of ceramic plate, ceramic plate plug serious suction effect will become worse (filter cake moisture content increased, cake thickness reduction), cleaning of ceramic plate refers to washing and cleaning.Backwash to ensure that the water filter filter water pressure in the 0.1MPa or so, at least not less than 0.07MPa or less, it is necessary to consider before the filter water pressure is low or water filter element needs to be replaced.Joint cleaning to ensure that the ultrasonic can be no trouble, every time cleaning the amount of nitric acid up to standard. If the filtration effect is not ideal, the cleaning cycle can be washed from 45--60 every 8 hours, changed to 6--7 hours and cleaned for more than 1 hours.
- Q:Ceramic filter suddenly do not smoke, a little later on their own good, what reason?
- The size of ceramic filter is generally on both sides of the vacuum tank, such as 50 square meters with 5 square meters of ceramic filter / ring ceramic filter plate combination (possible), there are 10 discs, the ceramic plate left a vacuum tank on the left of the 5 disc for filtration, vacuum filtration tank for the ceramic plate on the right right of the 5 disc. If a vacuum system temporarily fails, it may cause poor suction, no suction, and a normal operation at the other end.
- Q:The vacuum degree of the ceramic filter is normal and the cake water is large
- The vacuum degree of the ceramic filter is normal at about -0.08MPa. Under normal circumstances, the water content of the filter cake treated with a ceramic filter is about 10%, and the moisture content of the tail filter cake is about 15%. The water content of the filter cake increases with the increase of water content in the ceramic filter. I analyze the reasons from two aspects.
- Q:How to determine the quality of ceramic fiber filter board simply?
- Ceramic fiber filter board, in fact, ceramic fiber board, also known as aluminum silicate, refractory fiberboard.
- Q:What is the reason that the whole ceramic filter does not attract ore?
- After the joint cleaning, 0~2 hours of suction effect may be good, 2~4 may drop slightly, 4 hours later will become worse and worse, or even suck. This case should first check the backwash water pressure (instantaneous maximum pressure should not be less than 0.08MPa) is to meet the requirements, should also advance down (to ensure normal and ultrasonic cleaning combined with nitric acid dosage sufficient) and prolong the cleaning time.
1. Manufacturer Overview
|Annual Output Value
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
|No.of Employees in Trade Department
|No. of Production Lines
|Product Price Range