Wheel Loader with DEUTZ Engine
•DEUTZ Engine TD226B-6
•Single-turbo hydraulic torque converter and countershaft gear box
•Feicheng drive axle
•Two-way valve for lift arm and bucket
•Lift arm cylinder and bucket cylinder
•Standard lift arm
•Caliper disc brake
•Alternator 28V 750W
•Motor 24V 4.2
• The design for automatic dust removal of engine exhaust is good for maintenance;
• Single-turbo hydraulic torque converter together with countershaft gear box, this simple
makeup enables convenient repair and high work efficiency;
• 4-wheel caliper disc braking system ensures safer and reliable operation;
• Steering system adoping constant current exposed circuit steering system makes steering performance
at different speed and linear travel stable;
• Higher dump height and bigger dump reach can satisfy more work requirement;
•z-form connecting rod has strong break out force and high raising ability and enables high operating efficiency;
• Support of two rocker-arms enables stable performance;
• A broad view and a comfortable seat enable easy and flexible operation;
• Knock-down cab enables a wide work range;
• Rational matching parts, superior machine performance and extraordinary operating efficiency;
• Various optional equipment and buckets can satisfy different needs of customers.
Performance parameters of entire machine
Rated loading capacity
Digging Depth(bucket lean forwards 10 degree
Number of shifts (forward reverse)
Fuel tank capacity
Hydraulic fuel tank capacity
Total cycling time
Forward gear Ⅰ
Forward gear Ⅱ
Reverse gear Ⅰ
Optional Equipment (with different payment)
ROPS(roller protective structure)
Loose material bucket,
rock bucket, quenched
integral cutting edge bucket
Side dump device, clamping (Pipe or grass) de vice, high dump device
Cool air, warm air,
air-condition (cool & hot)
- Q:Loader tires 23.5-25-16PR what do you mean?
- 23 is the tread,.5 represents 90% aspect ratio, behind no problem.This kind of tire is usually used by loaders, so that the flat side of the tire is less than 10% of the width in order to lower the center of gravity.
- Q:Lingong loader certificate no no number is true
- Lingong loader certificate no no number is not really
- Q:What material does the ZL-12 loader bucket use?
- Also use Q235A bar, the car is estimated not to use 16Mn
- Q:How can I repair the pressure in the loader gearbox?
- (three) the gear box oil level of the oil level is too low when the gearbox oil level is too low, the oil cycle to work up transmission oil in the residence time of oil bottom and natural cooling time is short and the cooling effect is poor, resulting in transmission of fever, will also cause the hydraulic pump suction air, resulting in the decrease of pressure in the system. This kind of failure, strain gauge pressure instability and large swing, the engine speed changes, pressure gauge readings without big changes, indicating that driving hydraulic pump has suction phenomenon or inlet pipe leakage phenomenon. Should always check the oil level and add sufficient hydraulic transmission oil, if found leakage, timely maintenance. The oil level is too high. The oil level is too high transmission high speed rotating element around too much oil, the friction resistance increases, the oil temperature rise and converted into heat energy to participate in the work of the oil circulation, slow heat can not be distributed in a timely manner, and the backlog gradually with the extension of working hours, the temperature increased. (four) continuous high load loader such as long time high load operation, the heat generated in the cooling speed is fast, the working oil temperature will overrun, the temperature reaches a certain level will have a great damage to the moving parts, so it is prohibited for a long time overload operation when the ambient temperature is high, more attention should be paid to. To sum up, in order to avoid the transmission oil temperature is too high, users should strengthen management, according to the provisions of the use and maintenance, to avoid oil shortage, water shortage and long time overload operation and so on.
- Q:Solid tyres for loaders
- Shanghai Tire Co., Ltd. was founded in July 2006. Its capital involves solid tire, industrial tire production and sales, and is in the leading position among its peers.
- Q:Loader maintenanceThe ammeter in the loader is light, please ask the reason
- Maintenance is to play butter, check whether the instrument is normal, to see whether the body has oil leakage, check the oil brake oil enough
- Q:What do you mean by the R L of the loader's steering machine?
- Wheel loader English abbreviation, generally speaking, loader number is composed of three sets of symbols:1, the first group is the first English letter, general said the manufacturer or product models, such as ZL wheel loader, LG on behalf of lonking or job, FL on behalf of Futian leiwo, X (G) on behalf of the Xiamen, CG as the representative, is the abbreviation of the name of the manufacturer.2, second groups of numbers, usually 3 bits, such as 936855853 and so on, the general is the first manufacturer of his own name, not what the actual significance, second general models such as the tonnage of 3 tons, 5 tons, third general technical platform manufacturers, generally refers to the wheelbase, configuration and so on. If it is two, for example, 3050, directly represent the product tonnage.3, some manufacturers in the digital behind there is a letter or Greek letters, such as LL956F, ZL50C, ZL50- II is also the platform or product for the first few generations mean.
- Q:How much is the hourly fuel for excavators and loaders?
- Excavators are about 18-42 litres an hour. Less bulldozers, about 10-20 liters. Note that different brands, different power.
- Q:Is the loader driver a special type of work?
- Loader driver is a special type of work, as follows:I. brief introduction of special types of work:Special work refers to the work of special posts collectively, refers to the prone to casualties, the operation of himself, others and the safety of the surrounding facilities, there is a major hazard to the work. The former State Ministry of labor in underground, high altitude, high temperature, heavy physical labor and the range of toxic and harmful types as special types and clear special types are determined by the industry department or the Department of labor. Special types of work, different from special operations, are two different concepts.Two, detailed examples of special types of work:1. electrical work. Including power generation, power transmission, power transmission, electrical distribution, electrical equipment installation, operation, maintenance (maintenance), test workers, underground electrical fitter;2. metal welding and cutting operation. Welding and cutting operator;3. lifting machinery operation. [including crane driver, cable operator, signal conductor, installation and maintenance worker]4. driving motor vehicles in enterprises. Drivers of all types of motor vehicles including the production areas and construction sites within the enterprise, docks, freight yard, etc.;5. uphill erection work. More than 2 meters above the height of erection, demolition, maintenance, high-rise building (construction) building surface cleaning workers;6. boiler operation (including water quality test). Operator of pressurized boiler, boiler water quality tester;
- Q:Dragon 850 loader fuel tank capacity?
- 4, reduce the impact and vibration of the hydraulic system impact mainly occurred in the transformer, variable speed, reversing, the pipeline flow in the liquid due to the sudden closure of valve and reversing quickly of high peak pressure formed instantaneously, the connector, connector and flange looseness or sealing ring into the gap of damage caused by leakage. In order to reduce the leakage caused by shock and vibration, the following measures can be taken: first, all the tubes are fixed with a damping support so as to absorb shock and vibration energy. Adopt a reversing valve with damping, a slow switching valve, and a buffer device (such as one way throttle valve) at the end of the hydraulic cylinder. Use a low impact valve or accumulator to reduce impact. Arrange the pressure control valve properly to protect all the components of the system. Minimize the number of pipe connections, and use the welded connections as far as possible. The use of direct screw head, three joints and elbow instead of tapered pipe thread. We try to use the oil return block instead of each configuration. The maximum pressure for the specified torque used when installation bolt and plug torque, prevent the junction surface and the seal is damaged. 5, reduce the wear of dynamic seals. Most of the dynamic seals in the hydraulic system have been accurately designed. If the moving seals are machined properly, installed properly and used properly, long time no leakage can be guaranteed. From the design point of view, the following measures can be used to prolong the life of the dynamic seals. First, eliminate the radial load on the piston rod and the seal of the drive shaft. Protect the piston rod with dust ring, protective cover and rubber sleeve, prevent dust and other impurities from entering. Design and select the proper filter and easy to clean tank to prevent the accumulation of dust in the oil.
1. Manufacturer Overview
|Annual Output Value
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
|No.of Employees in Trade Department
|No. of Production Lines
|Product Price Range