Pvc Suction hose for Water pump

Ref Price:
Loading Port:
Qingdao
Payment Terms:
TT OR LC
Min Order Qty:
-
Supply Capability:
10000ROLL roll/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

pvc suction hose

 

Specifications

Specifications of suction hose:
1) Dimensions: 0.8'' - 6"
2) Material: PVC
3) Color according to client's requirements  

Pvc suction hose

Inch

I.D(mm)

O.D(mm)

5/8

14

18

3/4

19

23

2

50

58

3

75

83

Features of suction hose:
1) Made of highly elastic, high strength rigid plastic wire and superior PVC synthetic
material
2) Reinforced rigid plastic wire screw inserted into the inner wall of flexible PVC hose
3) Transparent tube body for high visibility of the fluid conveyance and eased control
of flow rate
4) Light, highly flexible with low bending radius
5) Widely used for the discharge and suction of fluids, gases, oils, and dust in
agricultural pump, oil warehouses, and petrochemical industry


Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:PVC plastic pipe in the underground, what need to diameter, the hoop and flange is a kind of thing?
The flange is the part that connects the pipe to the pipe and is connected to the end of the pipe. Flange connection or flange connection, is defined by the flange, gasket and bolt connection between the three sealing structure of the detachable connection as a combination of group pipe flange refers to the pipeline installation of piping flange, used in equipment refers to equipment import and export flange. The flange is lined with bolts to secure the two flanges. Gaskets for gaskets between flanges. Flange, threaded joint flange and welding flange.
Q:would you prefer plastic tubes over metal tubes I'm doing statics so i wanna know ur opnion?
depends on the use and application. would you prefer orange juice or lemon juice ? depends on your taste...... same thing. so it depens on many thing : cost, fluid to flow, medium temp, pressure, humidity, load type and so on .... good luck.
Q:A plastic tube allows a flow of 13.3 cm3/s of water through it. How long will it take to fill a 220 cm3 bottle?
220/13.3=16.5
Q:Need some pipes or tubes to make homemade ferret tunnels throughout bedroom?
Why not stop by your local department stores gift wrapping department and ask them for their left-over tubes? (The tubes they have are the ones inside their roles of wrapping paper which are the perfect size for ferrets...I know, I have some myself. hehe) You will sort of look like an idiot asking the employees for them but what the heck!! Put on your best smile and ask. They are free AND they were just going to throw them out anyway. And if this makes you feel better, I used to work at a department store when I was much younger and people would ALWAYS come in and ask for empty boxes and cardboard. Its fairly common. ;)
Q:what cage should i get for my teddy bear hamster? plastic with tubes or wire with platics bottom?
wire with plastic bottom because teddy bear hamsters can get very big and may not ne able to fit through the tube and also there is not enough air ventelation in all plastic cages. with can make it very humid in the cage and it will smell more
Q:Where is the a/c evaporator condensation drain tube on a 1998 Dodge Stratus? What's the best way to clean it
The drain will be on the passenger side, towards the bottom of the firewall. It should be below the 2 heater hoses that go intot he heater core. On yours, I think it was just a tube coming out of the firewall, it will have a foam gasket around the platic tube. The tube will protrude from the firewall just a little bit. Some have a 90 degree rubber elbow on the end of the tube. If it is just the plastic tube, without the elbow, then use either a wet/dry vac if you have one, or use a wire hanger to poke into the hole and try to remove whatever is blocking the drain. If you don't get it out, it might block it again later, or it might come out with the water. If you have the 90 degree rubber elbow, a quick trick is to squeeze it at the very end and roll it between your fingers to loosen the blockage. If that doesn't work, remove the elbow and clean it out, it will generally have the blockage in it. The elbow should have 2 pieces of wire sticking out, just squeeze these together and slide it off. Might have to give it a twist to get it to come loose. If you get the elbow off and water doesn't come rushing out, then clear the plastic tube, and check the elbow to be sure it isn't clogged.
Q:I would like to make a tube pour-in machine how do I go about it?
These are complicated electro mechanical devices.Another way would be to look at any patents filed explaining the principles of operation and come up with your own simplified designs that you may be able to build yourself, or get built for you.
Q:Doubts about the connection of plastic pipe and steel pipe flange
We have done such a job, generally can not match the diameter of the flange, just like the 110PPR pipe flange, and if the pipe flange connection, then use 150 of the flange, and then in the variable diameter to connect the steel pipe.
Q:How long of tubing can you use for a refrigerator ice maker tubing?
You can. Most kits for water supply come with 15 or 25 ft of tubing. You might consider buying bulk 1/4 copper tubing so that you won't have any joints in spaces that you can't get to easily. One solid run would be best. If you were going to run the plastic tubing I have never seen it in lengths greater than 25 ft. If you cant get a longer piece you should be careful where you make a joint.
Q:Can you eat coloured icy poles in the plastic tubes with braces??
Sure, just make sure to brush your teeth after to get rid of the sugar from the pops.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range