LED TUBE LIGHT 8W 60CM RA>70 PF 0.6 AC180-265V INPUT VOLTAGE 800LM GLASS MATERIAL
- Loading Port:
- ShangHai
- Payment Terms:
- TT ,LC AT SIGHT
- Min Order Qty:
- 10000 pc
- Supply Capability:
- 100000 Pcs Per Month pc/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
LED Tube Light are receiving global recognition for their energy saving capabilities, long service life ,easy installation and the ability to reduce carbon emissions across a host of different sectors.
Specifications of LED Tube Light Voltage:AC85-265V 50/60HZ 8W 60CM Beam Angle:300 degree
LifeSpan :30,000 Hours
2-3 years warranty
CRI :RA>70,RA>80
CCT;3000-3500K,4000-4500K,6000-6500K
Features of LED Tube Light
The LED Tube Light is widely used and are designed and manufactured to replace the traditional grille fixture ,CFL tubes , the superior SMD LED solution and purity Glass material makes the luminous efficacy high to 100LM/W, it is of excellently heat managed by conjoint structure which maintains the LED working temperature in a comfortable condition.
Excellent Heat Sink
SMD LED solutions
Superior High Quality
Eco-friendly
Energy Saving Perfect Replacement for All Lamp
Blast Free, Starter Free
Applications for LED Tube Light
Replacement CFL for traditional lamp, such as store, supermarket, commerical builing and anywhere
- Q:What is the reason for the movement of light in the tube
- Lamp tube problem, get a hot towel tube to wipe, sometimes can solve.
- Q:What happens when daylight lights go on
- What you're talking about is a buzzing sound, which is caused by the use of an old-fashioned inductive ballast, which suggests replacing an electronic ballast so that there is no sound
- Q:The lighting is replaced by LED lights and circuit problems
- No, you're going into a ballast, one is out. The picture you gave is only part of it. When you disconnect the ballast, connect the same color. The red one is the wire, the current of the ballast. After disconnecting, it should be a connection between the red wire and two broken wires. You should shoot the right wire again. The situation in my home was to tear down the ballast and the two red lines were connected to the red line. The green earth line connects to the blue line. You have to capture the essence of the problem, and you have to see the current flowing. The current must be in and out of the ballast. When you disconnect the ballast, you should connect the broken one to the other. This will make the current pass.
- Q:How many lumens is the T5 bulb of 18W
- The fixed bar is still rolling. Let's try a VGA line, if I can't do that, that's the problem of the screen itself. Like screen drive or line problems, not the LCD panel itself.
- Q:How to drive LED fluorescent tube with electronic ballast
- It's almost impossible, haha, the two principles are different.I hope my answer will work for you.
- Q:The same thing is 5w, is this LED tube power or is this a fluorescent lamp?
- In addition, under the condition of equal brightness LED lamp power is only 1/3 of the ordinary energy-saving lamps, so the same space, if use 20 w fluorescent energy-saving lamp tube, then switch to 8 wled lamp is bright enough. From this point of view, the electricity is greatly saved.
- Q:Is there a ballast in the LED lamp? Or do you need a ballast?
- LED lamp and fluorescent lamp works entirely different, the latter is gas emitting light source, the LED is a light-emitting semiconductor devices, so the driving mode is not the same.
- Q:What kind of lamp tube is the 2G11 lamp of LED fluorescent lamp
- It's a lamp holder, which is different from T8 T10. The spacing of the pins is different. Look at figure 2G11. If you don't understand, you can add me Q9, 5, 3, 4, 7, 2, 5, 3, 2
- Q:Is it healthy to hang a towel with a bad fluorescent lamp
- Mercury vapor reaches 0.04 to 3 mg, which causes chronic toxicity in two to three months. An increase of 1.2 to 8.5 mg can cause acute mercury poisoning, and if it reaches 20 mg, it leads to death.
- Q:What installation is the T8 LED tube?
- Remove the regenerator. Just plug it in. Of course, look at what you bring without an external supply. If there's an external power source, it's a bit of a hassle. To read the instructions, follow a picture. LED lamp tube appears to be able to connect the ballast to do not want, save a bit to expend
1. Manufacturer Overview |
|
---|---|
Location | |
Year Established | |
Annual Output Value | |
Main Markets | |
Company Certifications |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | |
No.of Employees in Trade Department | |
Language Spoken: | |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
LED TUBE LIGHT 8W 60CM RA>70 PF 0.6 AC180-265V INPUT VOLTAGE 800LM GLASS MATERIAL
- Loading Port:
- ShangHai
- Payment Terms:
- TT ,LC AT SIGHT
- Min Order Qty:
- 10000 pc
- Supply Capability:
- 100000 Pcs Per Month pc/month
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Related keywords