T8 LED Tube SMD Chip High Efficiency 1.5M 18W

Ref Price:
$9.48 / pc
Loading Port:
Shenzhen
Payment Terms:
TT
Min Order Qty:
10 Pcs pc
Supply Capability:
100000 Pcs Per Month pc/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

T8 LED Tube SMD Chip High Efficiency 1.5M 18W 1. This product meets the standard of CE certification.
2. With internal No-isolated power supply.
3. Round and the elliptical tube are available.
4. Use the most mature international well-known LEDSMD2849 as the light source, which can ensure the led tub35 as the light source, which can ensure the led tube brightness and long lifetime, also can reduce the light decay.
5. Use the high quality aluminum PCB for LED’s better heat dissipation.
6. High-grade PC cover with nice light transmittance(> 95%),Transparent PC cover and frosted PC cover are available.
7. 180 degrees beam angle makes the lighting effect better.
8. CRI(standard products)>70,it can be over 80 if required.
9. Ambient temperature:-20°C-40°C, surface temperature: 42°C-45°C
10. No mercury, lead or other hazardous materials; no radiation, no electromagnetic radiation, no frequency flash, instant start up, no hurting eyes.
Applications:
Replacement for conventional fluorescent tubes:
1. Hotels
2. Conference/ meeting room
3. Commercial Complexes
4. Residential/ Institution Buildings
5. Schools, colleges & Universities
6. Hospitals General li

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:What's the matter with the light bulbs?
Tungsten electrode, turn off the light inside, inside with mercury vapour, through high pressure mercury vapour breakdown, and consumption of tungsten electrode, electric light, may be a poor contact circuit aging or light foot, if end black gathered themselves together, and it is also possible that a serious of tungsten electrode burning, still hope electrician check and to avoid an accident!
Q:How to meet? The rectifier is very easy to connect
The ballast electronic ballast is not very long. It is very easy to be bad
Q:How to detect the good and bad of the fluorescent lamp
If you measure the resistance at both ends, it's not bad
Q:What material is LED fluorescent lamp fittings, such as shell, block?
The bottom case is pure aluminum, solving the problem of divergence; The mask is a PC milky white or transparent to solve photoelectric transmission and visual effects. The plug is made of plastic, not easily broken and safe.
Q:Are led fluorescent tubes not available for lighting?
But to see if there is a built-in power source, the external power source is not directly 220V,
Q:What is the connection of the LEDT5 lamp tube, the main line is how to connect, only to the end
Yellow lines don't have to be yellow to be ground.I hope my answer is useful to you.
Q: The title What is the color temperature of the leds?
In the same way, the leds show that the index is higher, and the PC cover is about 85% control
Q:The LED fluorescent tube plus the ballast why is it still going to press?
The ballast is not the condition that the voltage is raised, and when it is energized, the generator switches in the circuit, which is connected by a neon discharge tube with a capacitor
Q:Are the old daylight bulbs worth recycling?
The fluorescent lamp doesn't seem to have a dedicated recycling system. Go to secondhand market transfer, after appearance is refurbished, again can use Led fluorescent lights are needed
Q:The lamp tube of LED lamp is full plastic lamp tube good or half plastic half aluminium tube good?
The whole plastic lamp tube mainly USES the non-isolated power source, in order to avoid the electric shock problem, so adopt the whole plastic lamp tube. It USES a phi 5 hat tube LED. The biggest problem is that the cooling problem, because all the heat sealed in tube, don't spread out, the light failure is severe, plus straw hat tube original life is very short, less than 2000 hours it broke. And half plastic and aluminum tube is the market sales of the LED fluorescent lamp is essentially the half PC alloy, in need of pervious to light the plastic, half without pervious to light and the need to adopt aluminum alloy heat dissipation of the half. The power is placed inside the aluminum tube, so the heat from the LED and the heat from the power supply is quite large, since the power of the lamp is usually around 20W. The power is larger, and the semi-aluminum tube doesn't solve the heat problem. Leds are English light emitting diode (LED), its basic structure is an electroluminescent semiconductor chip, silver white glue or adhesive curing to the bracket, and then use silver or gold wire connection chip and circuit board, and then sealed with epoxy resin around, protect the internal core, final installation of the shell, so the LED of the seismic performance is good. The area of application involves cell phones, lamps, electrical appliances and other household appliances and machinery production
We are a leading manufacturer of a broad range of LED strip light and LED Tube light. From 2011, we have integrating sphere spectrometer, high speed automatic placement machine, reflow soldering machine, automatic dispensing machines and other specialized equipment and professional R & D department. LED strip light can produce up to 300000 meters per month.

1. Manufacturer Overview

Location Shenzhen,China
Year Established 2011
Annual Output Value
Main Markets

Mid East;Western Europe
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port Shenzhen
Export Percentage
No.of Employees in Trade Department 20 People
Language Spoken: Chinese
b)Factory Information  
Factory Size: Above 4,000 square meters
No. of Production Lines About 5
Contract Manufacturing OEM Service Offered;Design Service Offered
Product Price Range Cheap