LED T8 Integrated Tube SMD Chip High Bright 1.2M 18W

Ref Price:
$9.30 / pc
Loading Port:
Shenzhen
Payment Terms:
TT
Min Order Qty:
10 Pcs pc
Supply Capability:
100000 Pcs Per Month pc/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

LED T8 Integrated Tube SMD Chip High Bright 1.2M 18W 1. This product meets the standard of CE certification.
2. With internal No-isolated power supply.
3. Round and the elliptical tube are available.
4. Use the most mature international well-known LEDSMD2860 as the light source, which can ensure the led tub35 as the light source, which can ensure the led tube brightness and long lifetime, also can reduce the light decay.
5. Use the high quality aluminum PCB for LED’s better heat dissipation.
6. High-grade PC cover with nice light transmittance(> 95%),Transparent PC cover and frosted PC cover are available.
7. 180 degrees beam angle makes the lighting effect better.
8. CRI(standard products)>70,it can be over 80 if required.
9. Ambient temperature:-20°C-40°C, surface temperature: 42°C-45°C
10. No mercury, lead or other hazardous materials; no radiation, no electromagnetic radiation, no frequency flash, instant start up, no hurting eyes.
Applications:
Replacement for conventional fluorescent tubes:
1. Hotels
2. Conference/ meeting room
3. Commercial Complexes
4. Residential/ Institution Buildings
5. Schools, colleges & Universities
6. Hospitals General li

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:How much is the ballast of the fluorescent tube coming out
Because the ballast is in a series in the circuit, the output voltage is constant in normal circumstances, It's just that the electric light starts in an instant and produces a 600v-1500v pulse voltage that lasts about 1ms
Q:How to drive LED fluorescent tube with electronic ballast
It's almost impossible, haha, the two principles are different.I hope my answer will work for you.
Q:What about the quality gap between leds?
First, the radiator: the heat of the radiator slowly decides the light of the light to fall. Second, power drive, power driven quality determines the whole life of the lamp bead, light bead almost all does not matter, but once the driver with the inferior, the LED fluorescent lamp is easy to burn out. The difference between light and light is that light is weaker than normal. Third, bead light, chip, encapsulation skill determines their price is different, different customers care about lamp bead size is 2835352 or 3014, you really should care about is the chip size and manufacturers. There are several reasons for the gap
Q:Ordinary fluorescent lamp ballast can be replaced with led daylight lamp tube
Your ballast is broken and you can change the ballast, or replace it with an LED fluorescent tube. Different brands need to be modified in different ways. Some dismantlement is ok. My house needs a ballast and a regenerator
Q:Is the normal daylight tube replaced by an LED line
Step 1: use a screwdriver and a pliers to disconnect the ballast from the wire. But my home is the sun lamp base of zhengtai, the quality is too good, it took 10 years. I didn't even get down to the ballast, which was stuck in a full thick iron base, so I disconnected the wire. The wire that disconnects from the ballast is sure to have two heads, just to disconnect the connection. There is a lot of direct skewers of black tape, some of which use that connector and screw the two wires together. It's the same thing. This is the connector that is used in this case. Disconnect the regenerator, remove the wire and then rewire the two broken wires together and attach the black tape (which is the insulating tape). Put the base back to the original. Install the fluorescent tube, and remember to place the head of the European logo on the base of the current. And when you put it in place, it's going to be OK.
Q:Put on LED lamp tube, can connect change 3 lamp tube not bright?
The problem should be: 1, your lamp holder is not in position; 2, the connection of the lamp holder is loose or the wire is broken. No short circuit at both ends of the rectifier. No short circuit in place on both ends of the rectifier, easily between the open flashing voltage is too high, if the LED lamp circuit withstand voltage protection, easy to damage, so suggest tear down ballast, connect the line again.
Q:How does the traditional fluorescent tube stand install led lamp tube reforming method
Replace the lamp and rectifier with LED and matching. Traditional fluorescent lamp or low pressure mercury lamp, is using low pressure mercury vapor release ultraviolet ray after electricity, which makes the principle of phosphor emit visible light, so it belongs to low pressure arc discharge light source.
Q:The LED T5 daylight lamp can be used for how long
In five years, are you sure you can find each other easily? If the warranty doesn't go away, you say no. The other person is said to be bao 5 years, that want to be sure, in 5 years the light of the year of the light to fall is normal, should be certain that the person of the other person 5 years of light to be not more than 15%, that is the real guarantee 5 years. If the light is more than 20 percent after four years, the light is still bright. If the bulk purchase can be measured by the illuminometer, then measure it every year. But you're going to do it for five years. In the case of 24 hours of use, it's pretty good to be able to control over 10% in two years. If the best use of the industry is to use an external drive power source, the heat dissipation will not affect each other, and it will last longer if the lamp is identical in quality. But the installation will be a little bit more cumbersome than the built-in one.
Q:What is the reason for the movement of light in the tube
Lamp tube problem, get a hot towel tube to wipe, sometimes can solve.
Q:How does the T8LED light tube replace the fluorescent lamp tube
Tube at both ends a firewire, on the other side is zero, the two feet per head are connected together, by one or two can be, if with neon bulb starter, starter can be twisted off, then remove ballast two joint together can change LED bulb.
Focus on environmentally friendly LED intelligent lighting products are obtaining CE, ROHS, CCC and other domestic and international authoritative certification; product sales in the domestic market to maintain continuous growth, and exported to Europe, America, Southeast Asia more than 10 countries.

1. Manufacturer Overview

Location Shenzhen,China
Year Established 2011
Annual Output Value
Main Markets

Mid East;Western Europe
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port Dongguan
Export Percentage
No.of Employees in Trade Department 50-100 People
Language Spoken: Chinese
b)Factory Information  
Factory Size: Above 1,500 square meters
No. of Production Lines About 5
Contract Manufacturing OEM Service Offered;Design Service Offered
Product Price Range Cheap