LED Tube Light are receiving global recognition for their energy saving capabilities, long service life ,easy installation and the ability to reduce carbon emissions across a host of different sectors.
Specifications of LED Tube Light
Beam Angle：300 degree
LifeSpan :30,000 Hours
2-3 years warranty
Features of LED Tube Light
The LED Tube Light is widely used and are designed and manufactured to replace the traditional grille fixture ,CFL tubes , the superior SMD LED solution and purity Glass material makes the luminous efficacy high to 100LM/W, it is of excellently heat managed by conjoint structure which maintains the LED working temperature in a comfortable condition.
Excellent Heat Sink
SMD LED solutions
Superior High Quality
Energy Saving Perfect Replacement for All Lamp
Blast Free, Starter Free
Applications for LED Tube Light
Replacement CFL for traditional lamp, such as store, supermarket, commerical builing and anywhere
- Q:Use LED fluorescent lamp tube to replace, the line of original daylight-tube seat should be refitted
- So old ballast, the ballast uninstalled, directly to the card on the two old fluorescent lamp wire short respectively, and then to the outside power, install the LED fluorescent lamp with respect to OK
- Q:If the body is accidentally broken, will it be electrocuted?
- No, only a small amount of fluorescent powder and gas will be slightly contaminated with the environment
- Q:How does the lamp line connect
- The one that used to be in the early part of the world, which requires the regenerator to cooperate with the light, is an inductance ballast, and the fluorescent tube now needs to glow without the regenerator. The ballast that doesn't need a regenerator is an electronic ballast. Ask to sell tubes of the owner, they all know and electronic ballast inductance ballasts, now basically eliminated inductance ballasts, everybody understand the electronic ballast is enough. If it is an old lamp, it will meet the inductive ballast. The lamp tube has two feet on each side, and the left and right sides are four feet
- Q:Homemade studio, what's the light? What light tube, cold light, warm light
- Homemade studio, the proposal USES small volume, energy conservation and environmental protection of the LED lamp, T5 and T8 is right choice, but it is best to choose the warm light, so that better color rendering.
- Q:What installation is the T8 LED tube?
- Electronic ballast installation: Turn off the power switch. 2, remove the electronic ballast from the lamp, and make the following changes to the lamp circuit 3, select the LED lamp, and turn the LED lamp down. Turn on the power switch
- Q:The reason for the slow start of an old-fashioned daylight tube
- The old fluorescent lamp is used to heat the filament of the lamp with the light of the regenerator, and the ballast produces high pressure when the regenerator disconnects
- Q:How to choose daylight lamp? What is the light bulb specification?
- The principle is: when the switch is switched on, the power voltage is passed through the ballast and the lamp filament to the two poles of the regenerator. The voltage of 220 volts immediately disassociates the noble gases of the regenerator, producing glow discharge. The heat of the glow discharge heats up the bimetal plates, and the poles are in contact. The current flows through the ballast, the regenerator, and the two ends of the filament. The filament is quickly heated by the current and emits a lot of electrons. At this point, the voltage between the poles is zero because the regenerator is closed, the glow discharge disappears and the temperature in the tube decreases. The bimetal strip is automatically reset and is disconnected. At the moment of the disconnection, the current of the circuit is suddenly cut off, and the ballast generates a large self-inductance, which is applied to both ends of the tube with the power supply voltage. The large amount of electrons emitted when the filament is heated, under high voltage at both ends of the lamp, is moving at maximum speed from low voltage to high potential end. In the process of accelerating motion, the argon molecules in the collision tube are rapidly ionized. Argon is ionized by heat, which causes mercury to produce steam, and the mercury vapor is ionized and emits a strong ultraviolet light. In ultraviolet light, the phosphor powder in the tube walls emits near-white visible light.
- Q:Does daylight bulbs damage electronic lamp heads?
- Will you get the power wrong? Maybe there's some protection on the lamp that the developer has lost, if you're the new one, you're going to go to the dealership.
- Q:How to remove fluorescent lamp tube
- Rotate the tube 90 degrees and remove from the gaps seen above. Is there a gap between the ends of the lamp holder? If you have to rotate it. If there is no gap, just look at the ends of the lamp holder, a paragraph should be active, you hold the lamp, it toward the activity period of pressure, on the other side can be removed. That's two
- Q:Is it healthy to hang a towel with a bad fluorescent lamp
- You're talking about fluorescent powder. Because of the high amount of Hg in the process of charge of fluorescent powder, the main source of its harm is its Hg vapor.
Focus on environmentally friendly LED intelligent lighting products are obtaining CE, ROHS, CCC and other domestic and international authoritative certification; product sales in the domestic market to maintain continuous growth, and exported to Europe, America, Southeast Asia more than 10 countries.
1. Manufacturer Overview
|Annual Output Value
Mid East；Western Europe
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
|No.of Employees in Trade Department
||Above 1,500 square meters
|No. of Production Lines
||OEM Service Offered；Design Service Offered
|Product Price Range