Heavy-Duty Marble Cutting Machine/CNC Router QL-1218

Ref Price:
Loading Port:
China Main Port
Payment Terms:
TT or LC
Min Order Qty:
1 Set set
Supply Capability:
100 Sets per Month set/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Detailed Product Description

Heavy-duty Marble Carving Machine(CNC Router QL-1218)Leadshine drivers

High precision and broad spectrum

  

Characteristics: 

1>imported linear square rails, dual four slider, loading capacity, smooth operation and high precision, long life, under the knife precision. 

2> The entire machine seamless welded steel structure, rigid Haobu deformation, table back lining plate, the rigid strength, and machine loading capacity can be 

3>constant power spindle motor, cutting intensity, high efficiency. 

4>software compatibility, and compatible with Typ3/Artcam/Castmate / Wentai, and other CAD / CAM design software 

5>two-way tool cooling system, effectively raising tool life

 

Scope:

Granite, marble, Qingshi, sandstone, and other stone carvings

Granite and other hard stone carving to be at level 5 mm

Marble, Qingshi, can be a sculpture to 5 mm

 

Performance parameters:

Performance parameter901512181325
X,Y Working area900mmx1500mm1200mmx1800mm1300mmx2500mm
Z Working area260mm260mm260mm
Table size1100mmx2000mm1400mmx2300mm1600mmx3100mm
Processing precision0.05mm0.05mm0.05mm
Reposition precision0.02mm0.05mm0.05mm
Table structurealuminiumaluminiumaluminium
X,Y,Z structureX,Y,Z ballscrewX,Y,Z ballscrewX,Y,Z ballscrew
CommandG CODEG CODEG CODE
Machine power2KW2KW2KW
Max processing speed6000mm/min6000mm/min6000mm/min
Max speed8800mm/min8800mm/min8800mm/min
Working voltageAC380V/50HzAC380V/50HzAC380V/50Hz
Spindle power4.5KW4.5KW5.5KW
Spindle rotating speed0-24000rpm/min0-24000rpm/min0-24000rpm/min
Drive motorStepperStepperStepper
Operation systemPCI CARD controlPCI CARD controlPCI CARD control

 

Guarantee & Aftersales Service:   

Guarantee for one year          

24-hour technical support by email or calling

User-friendly English manual and Video CD for machine using and maintaining

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Ask a question how to do the thimble hole of the shaft
Well, is this also the problem, R hole is dry this, and then better, repair the top pin ah...
Q:Will the injection molding machine test die, thimble white what is going on, what should I do, ask for help?
Try not involved in forming pressure, just when there is surface dent to check whether there is a white hat, such as the draft or ejection resistance problems, recommend die; if it is a problem of technology can reduce the pressure, pressure holding try.
Q:Where's the HUAWEI P6 thimble?
It's on the left hand side of the phone. There's a silver thing, and that's it. Just pull it out.It's also headphone hole.
Q:Injection rod hydraulic cylinder leak..
Aging of sealDirectly find manufacturers or hydraulic parts vendors repair
Q:Do you have UG drawing out of the die? How do you mean the thimble cylinder?
If the company does not have separate development plug-in, it will install a HB plug-in, which 2D modules have a variety of standard parts of the symbol.
Q:How does the EMX adjust the angle of an irregular flat thimble? (solved temporarily)
In the EMX thimble interface, there is an angle data in the lower right corner. You can enter any angle
Q:The mold tube thimble can not return to the designated position, the left and right sides have what is going on!
The situation you are talking about may be the following questions,1, the thimble plate sink too deep (see what you asked, should be checked, can be ruled out)2, our tube and the mold with smooth, tight when it is heated, so that the ejector plate back in place, but this problem will lead to other thimble will back in place, and only in the back needle short will appear this situation, or to be back pressure needle. You can check this again. If only the cylinder is higher, you should see whether the front of the thimble plate is too small or not. When the tube is out of order, the tube hangs in front of it. If it's good, it won't be possible unless the cylinder is of the wrong height. Or the barrel is stretched. Ha-ha3, your cylinder fits into the cage, and the rear side of the cylinder is too small to support.4, you said "just like back in place, flash out", this sentence, you did not go to the measurement of product is not short column two mm, the two began to die well, is behind. There is also a case of ejector pin back, making our cylinder the steps below our needle tube, that will also appear flash like this to confirm the ejector pin plate bolt can lock the screw end, and big enough, if the needle is large enough, is to end lock screw. If the needle is relatively small and long, on the way to do a Tozzi gatto, syringes and needles. If the needle is broken, you want to see the length, right? Is there too much preload?
Q:Injection molding machine mold thimble on the oil injection, the product also has a bit of anti rust agent, release agent, which kind of gasoline can be cleaned, the mold does not dismantle
As for a few products, only the gasoline can be cleaned, but the smell is large, and will remain for a long time.Mold cleaning agent is recommended.
Q:What is a "water gate" in an injection mold?
The affirmative answer for your brother is the puller! A lot of things inside the mold name is not the same, in fact, the role is the same, the name is not uniform everywhere, to bring doubts to beginners. If you have any questions, please leave a message for me. I specialize in plastic moulds.
Q:What browser can set the function of the thimble (always at the top)?!
You can download a small deskpin software, it can make the application always on top
With fine fitting parts and advanced technique, our products expand stably, in the fields of advertisement, carpentry, and metal molds. With superior performance-to-price ratio, high quality, and perfect post-sales service, the market share of our products expands unceasingly. We will unceasingly develop and innovation with our full enthusiasm, to carry forward our products and offer better products for our users.

1. Manufacturer Overview

Location Shandong,China
Year Established 2008
Annual Output Value US$5 Million - US$10 Million
Main Markets 11.11% North America
11.11% South America
11.11% Eastern Europe
11.11% Southeast Asia
11.11% Oceania
11.11% Mid East
11.11% Eastern Asia
11.11% Western Europe
Company Certifications ISO 9001:2000;CE Certificate

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port QINGDAO,TIANJIN,SHANGHAI
Export Percentage 71% - 80%
No.of Employees in Trade Department 6-10 People
Language Spoken: English, Chinese, Russian
b)Factory Information  
Factory Size: 5,000-10,000 square meters
No. of Production Lines 10
Contract Manufacturing OEM Service Offered Design Service Offered
Product Price Range Low and/or Average