Fiberglass pipe insulation

Ref Price:
Loading Port:
China Main Port
Payment Terms:
TT OR LC
Min Order Qty:
-
Supply Capability:
-

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Several advantages of glass steel pipeline with insulation:

(1) corrosion resistance: chemically inert material,excellent corrosion resistance, and can according to thedifferent choice of corroded pipeline conveying medium.

(2) high mechanical strength: water pressure resistance,resistance to external pressure strength and impact strength were good and according to requirements of thedesign and manufacture of pressure pipes and pipe fittings.

(3) temperature adaptability: use temperature range:more than -70 degrees Celsius lower than 250 degrees Celsius, the freezing medium pipeline without crack.

(4) small fluid resistance: pipeline smooth inner wall,roughness coefficient is 0.0084, the same flow, pipe diameter can be reduced.

(5) light weight, long service life, light weight, convenient transportation, low cost, no maintenance, the service life of 50 years or more.


Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:What is the amount of plastic profiles
The size of the sliding window lap affects the sealing of the window, safety, installation, daily use and so on. (12mm-8mm = 12mm), the gap between the fan and the ribs of the box (ie, the slide) is 12mm (20mm-8mm = 12mm). ), This gap for windows to install and pick up. When installing the window, the sash and bottom frame are only 4mm at the top of the ribs. Due to the size deviation of the window frame and sash, the straightness deviation of the window frame installation and the height change of the pulley used will change the actual overlap and installation gap of the frame fan. When the amount of overlap between the fan and the upper frame increases, the installation gap decreases, and the window fan is hard to be installed, and the frictional force of the window and the upper seal block increases, resulting in the opening of the sash; Sealing performance decreased, lap volume is too small, but also increase the risk of sliding window off.
Q:Plastic profile brittle extrusion process unreasonable reasons
Excessive or insufficient material This is related to the process temperature setting and feeding ratio. The temperature setting is too high to cause the material to be plasticized. Some of the components with low molecular weight in the component will decompose and evaporate. The temperature is too low. Fully welded, the molecular structure is not strong, while the feed ratio is too large cause the material heating area and shear increases, the pressure increases, easily lead to plastic; feeding ratio is too small material heating area and shear reduction, Resulting in less plasticized, whether it is plastic or plastic surgery will cause plastic profiles crisp cutting collapse phenomenon.
Q:Steel windows and aluminum windows compare which is more expensive
Lighting performance: Plastic window window lighting performance than the aluminum window difference, the block of a single component shading area than the aluminum window about 10%, vision and decorative effect is poor, is not conducive to building energy saving.
Q:What is the steel profile?
Simply put the profile is installed into a window that can still be seen after the outer surface. Such as the large and small faces of the box. While the middle glass trough installed glass and pressed after the invisible, that is non-visible surface.
Q:What is the material of steel
In the building construction is mainly used for sliding, sliding doors and windows, fence, pipe and ceiling material applications, through the new process is also widely used in automotive engine protection board, not only light weight, and good toughness, with just fine Nature, and sometimes also known as alloy steel.
Q:How plastic embossed profiles are made
Preloading To improve the quality of the product and improve the molding efficiency, the powder or fibrous molding compound is pre-pressed into a certain shape.
Q:The difference between steel and aluminum alloy profiles
The quality of steel doors and windows is very difficult to identify, steel doors and windows of the steel liner standards should be GB 1.2mm, but you buy after the identification of its compliance, it is very difficult. But the broken bridge aluminum doors and windows in the identification of the quality is relatively easy, broken bridge aluminum window wall thickness standard is 1.4mm, the door profile thickness of 1.6mm, these thickness is on the surface can be Depending on the measured, so after the identification on the purchase, it is very easy. Another point to note is that no matter what kind of profiles you choose the doors and windows, we must focus on the strength of the manufacturers and workers of the technology, doors and windows performance is playing a good effect, depends entirely on the manufacturer's design, measurement , Installation and production. No matter what kind of profiles of doors and windows, to become a good door and window, are three points for seven installs. Obviously, the installation of technology is much more important than the type of selection.
Q:Is the powder produced when the crushed plastic is crushed?
1, plastic shredders and power units to be installed firmly. If you need plastic crusher long-term fixed operation, it should be fixed on the basis of cement; if you need plastic crusher flow operation, the unit should be installed in the angle made of iron on the base, and to ensure that the power machine (diesel or motor) and plastic The pulley groove of the crusher is in the same plane of rotation. 2, after the installation of plastic crusher to check the Department of fasteners fastening, if loose to be given to tighten. Also check the belt tightness is appropriate. 3, plastic shredder before starting, first hand rotation of the rotor, check the claws, hammer and rotor operation is flexible and reliable, broken room with or without collision phenomenon, whether the direction of rotation of the rotor and arrows in the same direction, Plastic crusher lubrication is good. 4, do not casually replace the pulley, to prevent the speed is too high to cause the explosion chamber explosion, or too low speed affect the efficiency of the pulverizer. 5, plastic shredder should be maintained after the first start idle 2 ~ 3min, no abnormal phenomenon after feeding work. 6, the work should always pay attention to the operation of the plastic crusher, first of all, to be uniform to prevent the blockage of waste room; Second, do not work for a long time overload. If you find a vibration, noise, bearing and body temperature is too high, such as spraying out of the phenomenon, should immediately stop checking, troubleshooting can continue to work.
Q:The state of high-rise residential building doors and windows materials are not allowed to use steel profiles are expressly provided?
Allows the use of steel profiles. The provisions of the doors and windows with the number of layers does not matter. Now energy-saving requirements, no matter what material, as long as the energy-saving requirements on the line. Aluminum need to use heat type, more expensive, so the use of steel is more common.
Q:The main features of steel profiles
In the building construction is mainly used for sliding, sliding doors and windows, fence, pipe and ceiling material applications, through the new process is also widely used in automotive engine protection board, not only light weight, and good toughness, with just fine Nature, and sometimes also known as alloy steel.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range