Q:What is the difference between Z41X gate valve and Z45X gate valve?

There is no difference in function. The two models are mainly made of different sealing materials,

Q:What is plug welding gate valve?

Socket welding valve refers to the use of socket welded connection valve.Simple socket welding is to insert the pipe into the gate joint to weld.The form of socket welding is mainly used for welding small bore valves and pipes, fittings and pipes. Small caliber pipeline wall thickness is thin, and error prone edge ablation, butt welding is difficult, more suitable for socket welding. In addition, the socket of socket welding has reinforcement effect, so it is also used under high pressure. But socketweld also has disadvantages, one is the stress condition is not good after welding, easy welding penetration, pipe inside a gap, so should not be used for piping system of crevice corrosion sensitive medium pipeline system and clean high requirements for socket welding. In addition, ultra high pressure pipeline, even small caliber pipe wall thickness is also very big, can use butt welding connection, as far as possible to avoid socket welding.

Q:What does valve qz45x - 10q mean?

Crown valve pressWhat does Q stand for? I'm not sure. It's probably made of ductile iron"Z" means "gate valve"4 represents flange connection5 represents the dark bar (1 represents the Ming pole)X stands for rubber seal and soft seal10q stands for 10 pressure

Q:Which is the most expensive, check valve and gate valve?

In the case of DN50 Z15T-16 DN50: screw valve 46.200 thread copper bar gate valve Z15T-16 DN50 52 Z45F-16 DN50 97 flange valve flange valve rod Z44T-10 DN50 169 Z45T-116 DN50 flange valve dark bar 173 thread swing check valves DN50 52.090 thread straight type check valve DN50 57.280 flange screw check H44T DN50 129 flange valve lift check valve H41T-16 DN50 124

Q:What does the gate valve 150# mean? Is it stress PN? What's that, PN16 or?It's better to have some specific links, thanks!

150Lb (American Standard pressure value corresponding to the PN2.0)

Q:Z45T-10 what kind of material is the gate valve?

Z45T-10 refers to the nominal pressure of 1Mpa gray iron valve. The meaning of letters and numbers is:(Z) - gate valve;(4) indication - internal thread connection;(5) indicating dark wedge rigid single gate;(T) - the body is made of copper or copper alloy;(10) indication nominal pressure 1 mpa.Is the gate valve opening and closing parts, RAM direction of motion perpendicular to the direction of the fluid, valve can only be fully open and fully closed, can not be adjusted and the throttle. The gate has two sealing surfaces, and the two sealing surfaces of the most commonly used gate valves form wedge and wedge angle valves.

Q:What is an inverted seal gate valve?

When the inverted sealing gate valve is fully opened, the sealing of the sealing is brought together, and the sealing effect is reduced, and the erosion of the filling to the fluid is reduced, and the service life of the filler is prolonged, and the possibility of leakage is reduced. Generally on the gate valve, stop valve has inverted sealing requirements.

Q:What is the difference between an elastic gate valve and a rigid gate?

Brief introduction: the valve gate valve is a gate opening and closing parts, RAM direction of motion perpendicular to the direction of the fluid, valve can only be fully open and fully closed, can not be adjusted and the throttle. Gate has two sealing surface, the most commonly used mode gate valve of the two sealing surface to form a wedge, wedge angle with valve parameters vary, usually 50, medium temperature is not high when 2 degrees 52'.Wedge gate valve can be made into a whole, called the rigid gate; can also be made to produce micro deformation of ram, in order to improve its process of deviation, make up the sealing surface angle in the process, the gate is called the flexible gate.

Q:The legend of gate valve and stop valve

The working principle is different. The stop valve is an upward stem type, and the handwheel rotates and rises with the stem. Valve is hand wheel rotation, stem upward movement. Flow is not the same, the gate valve requires full open, the cut-off valve is not the same. The gate valve has no inlet and outlet direction requirements, and the cut-off valve has the required inlet and outlet!Gate valve and stop valve are shut-off valve, is the most common two valves.From the exterior, the gate valve is shorter than the cut-off valve, especially the bar valve needs a higher height space. Valve sealing surface has a certain degree of self sealing capacity, its spool depends on the media pressure tight contact with the valve seat sealing surface, to achieve tight leakage. Wedge gate valve spool angle is generally 3~6 degrees, when forced to shut down excessive or temperature changes of the valve core is easy to die. Therefore, high temperature and high pressure wedge gate valve, in the structure have taken certain measures to prevent spool stuck. The valve in the opening and closing valve and valve seat sealing surface contact and mutual friction is always so easy to wear sealing surface, especially in close off the valve, the valve before and after the great pressure, sealing surface wear is more serious.

Q:What kind of valve is gate valve? Is it different from the cut-off valve?

Gate valve and the role of the cut-off valve, are playing a role in isolation. The difference is that the gate valve and the cut-off valve are constructed differently. Fluid from the gate valve flow and flow direction is straight, there is no change in direction, but in the cut-off valve is from the bottom of the valve flow into the flow from the upper part of the spool.