Quick Details of ANSI Globe Valve For Water, Gas and Oil
Standard or Nonstandard:
Temperature of Media:
WATER, GAS ,OIL
Place of Origin:
ISO9001, CE, API
Packaging & Delivery of ANSI Globe Valve For Water, Gas and Oil
WOODEN PALLET/ CASES
25-30 DAYS AFTER DEPOSIT
Specifications of ANSI Globe Valve For Water, Gas and Oil
1) valves range from 3/4" - 8"
2) export to overseas
3) More than 20 years manufacture experience
Usage of ANSI Globe Valve For Water, Gas and Oil
1) Size: 1/2"-2"
2) Pressure: 800lbs/1500lb
3) Applicable temperature range:
4) Material: WCB A105
5) Applicable medium: water, oil, gas
- Q:What kind of valve is it? How do you see the status of the switch?
- Globe valve, not ball valveClockwise (Bell) needle to reduce the flow to the end of the shutdown, the counter clockwise to open. You can turn the multi circle plate will also lift up and down. The spindle, to the top is open, down to the edge off.The ball valve has a strip handle, the line is connected, and the cross is turned off
- Q:Which valve can play a good regulatory role?
- A wide range of valves, the function is different, although like conventional butterfly valve, ball valve can play a regulatory role, but their role is not linear, so if you need to adjust the precision of the valve, it is best to select the control valve.
- Q:Valve and pipe correspondence
- If the valve from the opening and closing role, then the valve bore should be the same diameter with the pipe, big waste, small, increase resistance.If the role of the valve is adjusted, and that caliber will be different from the pipe diameter, this is not to reduce the cost of the problem, is a result of calculation, and this calculation results with flow, pressure drop and valve resistance curve.For example, control valve, usually smaller than the pipe diameter, such as pressure reducing valve, will be smaller than the pipe diameter to two.
- Q:Where is the hydrant main valve?
- The fire hydrant generally has two sources, one is from the roof water tank, a water pump is from the housing, maintenance, should close the fire hydrant located on the riser inlet valve tube under the ring, generally located in the top and bottom, and then discharge, when the valve cannot be closed, the proposed closure of replenishment valve and the pressure stabilizing device of water tank, fire pump in manual state, drainage after maintenance. Watch out for fire.
- Q:Yongde jiekelong valves and valves of the good faith
- Fujian Xiamen huashenghong Sanitary drainage fittings. Furniture guide rail, hardware, Taiwan locomotive. All of the above are the strongest domestic brands, high quality, stable performance, durable, buy a lifetime warranty, quality products. Domestic airport, water cube, bird's nest are using the above brand accessories.
- Q:What is the KVS in the valve parameter?
- KVS meaning in valve parameters:Kvs is the coefficient of flow (also called circulation capacity).Kvs refers to both ends of the valve pressure difference of 0.1MPa, water density of 1g/cm^3, when the valve fully open flow. It is an important parameter of the control valve, reflecting the capacity of the control valve.Flow coefficient is a unit of time, in the test conditions, the pipeline to maintain a constant pressure, pipe flow through the valve mass flow, or mass flow. That is, the maximum flow capacity of the valve. The greater the value of the flow system, the smaller the pressure loss when the fluid passes through the valve. The CV value of the valve shall be determined by test and calculation.
- Q:What is the flow medium of the valve?
- Valve flow medium refers to the valve through the fluid, gas and liquid.For example: water, air, oil, gas, steam, acid, alkali, gas, heat conduction oil and so on, are called medium.
- Q:Is the heat jacketed valve fitted with flanged flanges?
- Insulation valve is the standard valve, just in order to ensure the link bolt flange to super space, usually a large ball than normal level, such as the use of the path is DN80 flange, flange is DN100, so is the standard, but the size of flange connecting with other valves are not the same.
- Q:The water pipe in the house is broken.
- In general, a unit has a total valve. From this start, find it, find a less water when passing the total valve home to change, more energy, save trouble later. Or find the person of the company to deal with tap water.
- Q:What valve is the FCV?
- FCV is the control valve, you can adjust the valve opening according to the required flow.1, also known as the valve control valve, in the field of industrial automation and process control by adjusting the control unit outputs the control signal, the final control element with the power to change the media flow, pressure, temperature, level and other parameters. Generally composed of actuators and valves.2, according to the characteristics of the trip, the control valve can be divided into straight stroke and angular stroke. According to the power used by the executing agency, according to its function and characteristics are divided into linear characteristics, such as percentage characteristics and parabolic characteristics of the three. Control valve applies to air, water, steam, a variety of corrosive media, mud, oil and other media.
The company covers an area of 44000 square meters, building area of 35000 square meters, has a modern production plant and production equipment, production capacity of annual output of 20000 tons of low pressure cast iron valves. We have independent research and development capacity, according to user requirements for design and production.
1. Manufacturer Overview
|Annual Output Value
||South America; Western Europe; Eastern Europe; Southeast Asia; the Middle East
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
|No.of Employees in Trade Department
||44000 square meter
|No. of Production Lines
|Product Price Range