Angle Valve JBL-82-6116
The angle valve is brass body,chrome plating,beautiful design,high quality and sells good
(1)Brass body,chrome plating
(2)Modern design,high quality
(3)Many ranges are available
(4)OEM service offered
(5)Buyer label offered
Specifications of Angle Valve JBL-82-6116
Square angle valve,Brass body,zinc handle, chrome finished
1. Angle Valve
2. Brass body, zinc handle, stainless steel spout
3. Brass cartridge
4.With cross handle
Primary Competitive Advantages:
Country of Origin
Small Orders Accepted
Main Export Markets:
- Q:How to distinguish between full copper triangle valve and zinc alloy triangle valve?
- In general, the surface is bright and smooth, mirror effect is more obvious, the better coating process; two listen, listen to the sales staff introduction mainly for coating, triangle valve good not only experienced the pre grinding, polishing, dust, and up to six or seven layers of nickel and chrome plating coating process, the more, the better the quality;
- Q:Angle valve outlet angle how to adjust?
- Of course, the angle valve is constantly improving, although it is still three mouth, but there is not angle shaped angle valve. Industrial said angle valve: angle control valve in addition to the valve at the right angle, and other structures and through the single seat control valve similar.
- Q:Is the angle valve of the gas heater angle valve different from that of the toilet?
- It's the same.But note the following points:Note that the angle valve is the same caliber, so that it can be common;Angle valve, cold and hot water angle valve, it is best to buy hot water angle valve, so that the use of more time;In general, pure copper + galvanized zinc surface valve is relatively high grade better.
- Q:Angle valve in screw inside out how to do
- Usually used for faucet elbow into the wall too much, and the triangular valve can not be properly connected with the pipeline faucet elbow case to lengthen effect. Under normal circumstances, as long as the pipeline wall and a faucet elbow flat or slightly concave, and it is not necessary to use the wire connector..
- Q:Home improvement hydropower where to install angle valve?
- Corner valves are required for toilets, sinks and sinks
- Q:Can glass cement be used instead of raw meal belt angle valve?
- No, the raw tape is safer than the glass.
- Q:What are the specifications and sizes of household angle valves?
- Angle valve specifications are several, 15 turn, that is, four points; 20 turn, that is six points
- Q:What's the difference between a triangle valve and a three valve?
- This product is fully functional. The production of fine, the body of the product by refining brass forged, excluding the traditional sand casting production but the hidden Water Leakage blowhole; inlet thread adopts N tooth inserted process, convenient raw material for winding, non slip, completely close the thread, convenient installation, high strength, high pressure resistance, if damaged, continue to crack in the wall, light Loose change.
- Q:European standard angle valve, 3 to 4 angle valve
- Popularize knowledge:The bore of the water inlet pipe of the European standard faucet is connected with the angle valve, and the aperture at the end is 3,Angle valve is connected with the water inlet pipe and a leading GB braided tube caliber is 4 points,So you have to use 3 cents to 4 cents to meet the European standard angle valve.
- Q:When I was decorating the house, I found that there was no angle valve in the water tank of my washing dish. Do you have any idea?
- Not much impact, generally speaking, we should install the outlet faucet or angle valve, so that the day after opening and closing maintenance. Suggest that you let the decoration company to install one for you
Our sales network spreads all over the country, offering the nice services before & after sales. The products are produced with the forerunner's production equipment and consummate production technique, by making use of the management of science. Experienced inspectors carry out strict control in terms of product development, design, drawing, promotion, inspection, testing, monitoring and other procedures.
1. Manufacturer Overview
|Annual Output Value
||US$10 Million - US$50 Million
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
||41% - 50%
|No.of Employees in Trade Department
||3,000-5,000 square meters
|No. of Production Lines
||OEM Service Offered Buyer Label Offered
|Product Price Range