Q:Our house is only 60 square, a kitchen and a bathroom decoration company, before we hang wires, now listed a list of four points: a PCR ball valve, faucet elbow 12, angle valve 8, hose 3, number of these things??? Not much to it, that general faucet elbow 7 is enough..... Thanks for the answer.

The inner tooth elbow is the necessary equipment for each water, hot and cold water are themselves can count.Correspond to the number of equipment in your kitchen and toilet.

Q:Home toilet on the angle valve of Water Leakage, I changed a replacement, but after the emergence of a strange phenomenon, is the home of the water becomes super small, this is not only the main valve angle valve, the valve on the toilet, but why he changed after the whole house all the leading water becomes very small? Why? Why?To see clearly, oh, not the main valve, oh, put awayThe main valve has been switched many times, and the other one is very strange. When the other taps are changed, the place of the angle valve will hum

This problem occurs frequently, must spend more on the total valve closed angle valve replacement, after boiling water, the pipe rust with water to the total valve block caused by water becomes small, may also be the stem off. Turn on the tap and tap the main valve. If not, you can only open the main valve to clean or replace it. The local time for the other leading angle valve will hum sound, this situation is caused by the inferior angle valve, angle valve processing and installation error, causing the spool in a longitudinal direction of people, in other water when boiling water. The vibration of the pipe flow causes the vibration of the angle valve core, the noise made by the rotation of the angle valve and the non rotating part, just like the wind whistle of dove. When serious, it can cause pipeline vibration, and cause water hammer noise and resonance noise. If you do not often use the angle valve, you can use cloth to wrap the breath, you can eliminate this sound, or replace the angle valve, the purchase should pay attention to selection, there is no longitudinal accumulation.

Q:Can the water inlet and outlet of the triangle valve be interchanged?

Don't answer back.Although the triangular valve inlet and outlet after reverse can also be used, but from its internal structure, there should be import and export of points. The section is shown below:The lower port of the drawing is a water inlet, and the side is a water outlet. When the utility model is closed, the valve is closed to the water inlet, the water outlet is not provided with water pressure, and the switch part is not provided with water pressure, and the water can not leak out. If the reverse, pressure water enters from the side, whether the switch is on or off, the switch component is always pressure, there is no Water Leakage if things go on like this.

Q:Angle valve open and half open difference

4, beautiful appearance, so general bridal decoration are plumbing accessories indispensable, so the decoration new premises designers are mentioned, suggest to buy copper forging quality good angle valve, especially the 360 degree angle valve can adjust the outlet direction.

Q:The toilet is out of order and the water is kept running. The water overflows and how to turn off the water valve in the toilet, so that there is no more water in the tank

The toilet is on the left and right, on the wall. There is a tube leading to the back of the toilet

Q:Does the basin faucet need angle valve?

The angle valve, buy a durable stainless steel. Recommend SENTO to Amoy this brand. Taobao can buy.

Q:Ball core large flow angle valve why the noise of water flow?

Angle valve in accordance with the spool form, the valve core for the ball, can also be classified as a ball valve

Q:The angle valve is wrapped with several circles of raw material

3, when you tie the tape to tighten the raw materials, so that the raw material with a tight stick attached to the thread, as far as possible tight, do not loose loose, wrapped around to use hand circling compression, you can also press while wrapping.4, as winding several layers, there is no hard and fast rules, to tighten, do not leak as the standard, but according to experience, usually need to wrap more than a dozen laps to ensure the sealing effect.

Q:What are the specifications and sizes of household angle valves?

Angle valve specifications are several, 15 turn, that is, four points; 20 turn, that is six points

Q:Should the radiator be fitted with angle valves?

Angle valve is installed to replace the radiator and facilitate maintenance later. (even a water separator is recommended.)