Wall Lights For Bedrooms

Hot Products

Gypsum Board/ Drywall/ Plasterboard/ Interior Wall Panel

Gypsum Board ( Plasterboard ) For Wall

Gypsum Board Good Quality ,Low Price Acoustic Perforated

Gypsum Board/ Drywall/ Plasterboard/ Interior Wall Panel/ Paperbacked Plasterboard

Gypsum Board The Standard For Wall Partition

Gypsum Board Good quality Low Price Acoustic Perforated

Decorative standard size Gypsum drywall paper board

Gypsum Board Good quality Low Price Acoustic Perforated

Acoustic Perforated Decorative Panel, gypsum board, mgo board

Paper Faced Gypsum Board Manufacturers in China

FAQ

Gypsum board ceiling installation corner must be seven-shaped

This is not necessarily, as long as the long-term construction found in such a way, can be formed with the keel joints dislocation, in order to reduce the probability of cracks on the board.

Decorative gypsum board partition with what the best sound insulation cotton? Mineral rock wool and glass wool.

Sound insulation wall from the sound effects of rock wool and glass wool composite use of the best, rockwool isolated low audio, glass fiber cotton isolated high frequency, but rock wool is better, the bulk density of 80k or more. Construction is difficult, are almost, rock wool construction workers more uncomfortable, the price is still cheap glass wool

Gypsum board wall how to paste the footboard

Gypsum board wall flatness is very good, with 995 structure glue paste the base line is extremely fast, solid - in the backrest playing a few times on the back of the structure of plastic, attached to the required location on the line.

Duplex structure of the house, the lower part of the compartment hanging gypsum board ceiling problem

The center of the keel between the keel and the keel should be kept at 30 cm (we all do it), which is the normative requirement. Is the spacing of your I-beam exactly 30 cm? The Even if it is, even if he can put the screw into it, can do that, your top of the ceiling is definitely not flat.

What is the degree of grinding when the wall is polished?

With the light according to the wall to play, the light next to the wall to play well. With sandpaper of 320! Your own home to see what you ask yourself slightly, afraid of strenuous put the lights after the place to take care of the place to play a little bit, no light place a little grinding on the OK friends

Light steel keel gypsum board wall how to fight line?

This is just to find the vertical line on the line, first from the side of the wall, in the amount of a size, point a point, and then let the line down this point down to the ground, the other person to see the following line , In the ground point of a point, and then on the other side of the amount of a size you want, according to the above method on the ground and then point a point, and then on the top of the two points on the top line, the following two points bomb The ground line, and then the above points and the bottom points on the wall. If it is to the top of the partition, do not consider the level, only consider the vertical on the line,

Paper gypsum board non-stick paper and resurgence is what reason

Board ripples, pull ditch and other uneven phenomenon. The generation of such problems is related to paper indicators, process control and other issues. First, the paper factor. The amount of moisture, is not uniform, so that the paper is tight, different thickness, different water absorption, where the water is large, wet expansion is small, small water, wet expansion, in the dry The area of ??serious contraction, and the surrounding areas of less dry dry shrinkage, which resulted in the expansion of the paper, contraction is inconsistent, and cause ripples or pull ditch. Second, the problem of process equipment. The flatness of the molding platform is not enough or the adjustment is not in place, the same can cause the board uneven, this cause the problem is more concentrated, easy to find, but through the improvement of the process equipment to achieve the improvement of flatness of the board. Third, material and material fluctuations are also one of the important causes of uneven board. Due to fluctuations in raw materials, additional materials, and fluctuations in the milling process, it is inevitable that changes in the coagulation time and lift of powder and slurry are inevitable, but if the fluctuation is too frequent or fluctuating, Resulting in the subsequent process of the process is difficult to timely adjustment and control, can also lead to board groove and other undesirable phenomena.

Home improvement in light steel keel, gypsum board dragon card and can be resistant to which good?

Long card a little better now