wheel loader CDM810D,Hydraulic Load Sensor System

Ref Price:
Loading Port:
Shanghai
Payment Terms:
TT OR LC
Min Order Qty:
1 unit
Supply Capability:
10 unit/month
Inquire Now Customer Service

Contact us by

(1) WeChat
(2) Whatsapp: +8617190086776

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

 

Overall Data

Steering System

Bucket Capacity (m3)

0.5

Type

Hydraulic Load Sensor System

Rated Payload (kg)

1000

Cylinders-BorexStroke (mm)

2-63X280

Operating Weight (kg)

4200

Steering Pump

Shared With Working Pump

Traction Force (kN)

31

System Pressure (MPa)

14

Breakout Force (kN)

36

Steering Angle

±35°

I

II

Hydraulic System

Forward

8.3

20.8

Lift Cylinders-BorexStroke (mm)

2-80X610

Reverse

7.7

19.0

Tilt Cylinder-BorexStroke(mm)

1-100X450

Engine

Changchai  490B

Working Pump

Gear Pump

Rated Power (kW/rpm)

32/2400

Flow Rate (L/min/RPM)

120/2400

Rated Torque (Nm/rpm)

150/1800

System Pressure (MPa)

16

Starting Voltage (V)

24

Drive Train

Hydraulic Cycle Time, Rated Load in Bucket (In Second):

Torque Converter

Single-stage, Single-turbine, 3-element

Raise(Loaded)

Dump

Lower(Empty)

Total

Torque Ratio

3.7

4.5

01.2

2.2

7.9

Transmission

Fixed Shaft Hydraulic Shift Spur Gear

Electrical System

Gear

2F/2R

System Voltage (V)

24

Pressure of Transmission (MPa)

1.2-1.5

Battery(2 in series) (Ah)

180

Main Reducer

Spiral Bevel Gear Single-stage Reduction

Lamp Voltage (V)

24

Final Reducer

Planetary Reduction

Service Refill Capacity

Tire

11.00-16

Fuel Tank (L)

80

Brake System

Hydraulic Tank (L)

80

Service Brake

Air Drive, Four Wheel Brake (Dry)

Transmission (L)

16

Setting Pressure (MPa) Parking & Emergency Brake

0.78 Flexible Shaft Controlled Caliper

Front Axle (L) / Rear Axle (L)

8/8

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Working around some machinery/envelopes yesterday...?
There are men and women in this web page who will document others out of natural spite by the way, can I please ask EVERYONE to whinge approximately Violations whilst they aren't warranted.? A lot of men and women had been deleted just lately after operating very difficult to rise up to a degree wherein they are able to ask and reply limitless. If you get violated for whatever that's NOT even virtually being offensive, please document it with the e-mail header harassment through yet another person and state that you don't deserve this violation. Say that it's harassment and also you wish the problem investigated and the REPORTERS account suspended. I can be reporting EVERY one any longer Lets quit the senseless yobs destroying our paintings Just one factor despite the fact that. If you deserve the Violation - take it at the chin !
Q:How can I make ice without machinery?
Making Ice With Fertilizer
Q:How do you change the clock machinery so that in 1 day it would have gone round once instead of twice?
You need to change the gear ratio between the minute hand and hour hand, from 12:1 to 24:1.
Q:Where can I find Farm & Construction Machinery Industry financials?
Go to morningstar check out the financials of DE - John Deere CNH - Global NV CNH CAT - Caterpillar - they manufacture agricultural equipment, tho they are mostly constuction earth moving.
Q:Are Darwinian processes unlikely to have built the complex molecular machinery of the cell?
Well, it starts out lying about Lenski's long term E. coli evolution experiment. Being able to metabolize citrate is not a minor change. Being citrate negative is in the very definition of E. coli. The dishonest streak continues. They fully admit the group previously showed how it could have easily evolved from the proposed ancestral receptor. The reverse being unlikely doesn't affect a thing, since it didn't evolve in reverse. This is typical Evolution News and Views. They cannot directly challenge the overwhelming evidence supporting common descent, so they lie and distort data constantly. Edit: To be brief, for the receptor to evolve back to its ancestral state, first five separate mutations would have to happen. Each mutation kills the receptor, so genetic drift alone would be responsible. Once these five mutations are made, then the receptor could mutate to the functional ancestral form. This makes it very, very, very unlikely, but still technically possible. While interesting, this means little. The same group discovered only a few mutations are needed to switch from the ancestral to the modern form. Once there those five mutations each make its new function better, so there was a selective pressure for them, but they also locked away from the older state.
Q:Anyone have any tips on reading schematics for HVAC machinery? Or for wiring?
try taking a certification course at your local college.
Q:Explain why machinery used on a.c supply is usually rated in kVA instead of kW.?
Because most machinery present an inductive load and so has a less-than-unity power factor. The current peak lags the voltage peak in the two waveforms. However, as the current is drawn at a lower voltage (away from the peak), the load current is higher to get the same overall power to the machine. eg. if it took 20% more current to make up for the voltage phase offset, a 1000W load would be taking the same current as a 1200W load at unity power factor. That's the VA rating, it's equivalent to watts at unity power factor.
Q:Whats the biggest piece machinery you ever drove?
7 tonne forklift 10 tonne crane hugs xxxx
Q:Is there a way to cut, facet, and/or polish gemstones without expensive machinery?
hi an straightforward thank you to do it is to soak it in vinegar over night then replaced into off with heat soapy water make certain extremely dry earlier putting away back The vinegar is an exceedingly gentle acid it won't influence your sliver plate yet will influence the grease and dirt that assemble on it desire this helps
Q:Is it legal in the state of Florida for an employer to make an employee pay for damages on machinery?
did the boss approve the extra time did your shift supervisor approve it if no to the two then no they dont ought to pay you as you volunteered to do the extra advantageous artwork artwork nor authorized via administration beforehand of it being finished may be seen as volunteer artwork did somebody ask you to stay over if not you worked for unfastened regrettably its legal you chosen to stay and artwork without consent subsequently they dont ought to pay you

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range