Ustorm S10 Outdoor Fixed LED Display High Pixel Density

Ustorm S10 Outdoor Fixed LED Display High Pixel Density

Ref Price:

Loading Port:: China main port

Payment Terms:: TT OR LC

Min Order Qty:: 10 m²

Supply Capability:: 10000 m²/month

Inquire Now

Chat Online

Add to My Favorites

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

Ustorm S10(Outdoor Fixed LED display)

Features：

1. Completely sealed module design, All-weather & UV-resistant Outdoor LED display, guaranteed reliability under the toughest operation conditions

2.High reliability, excellent circuit design, no fans, lower power consumption

3.Easy to maintain, offering front and rear access for easy maintenance

4.Lightweight design with cabinet thickness of 100mm, weight of 31.25KG/SQM, these features help you save the cost of transportation as well as the cost of installation.

5 Cabinet size optional: 1200*1200mm or 800*800mm;

Parameter	Value
Pixel Pitch	10mm
Pixel configuration	1R1G1B
LED type	DIP346
Brightness	8000 cd/m2
Color temperature	H: 140°; V:60°
Viewing angle	H: 140°（+70°/-70°）; V:60°(-30°/+30°)
Pixel density	10000 pixels/m2
Recommended viewing distance	≥17 M
Module size	199.6mm×399.6mm
Cabinet size	W1200mm×H1200mm×D124mm	W800mm×H800mm×D119mm
Weight	50.5 kg/panel	20 kg/panel
Area	1.44 m2	0.64 m2
Material	Epoxy Paint Coated Aluminum
Aspect ratio	1:1
Ingress protection	IP65/IP54
Operating Temperature/Humidity	-20℃~+50℃/10~90%RH
Storage Temperature/Humidity	-30℃~+60℃/10~90%RH
Pixels per panel	60×60 dot	40×40 Dots
Processing depth	14 bits	14 bits
Brightness control	Manual/Automatic
Contrast ratio	2000:1
Video frame rate	50/60 Hz
Rate refresh	≥2000 Hz
Input voltage	110~240VAC
Input power frequency	47~63 Hz
Input power <max>	500W/m2
Input power <typical>	166.7W/m2
Driving Method	Constant Current Drive
Input signal	RF,S-VIDEO,RGBHV,YUV,YC & COMPOSITION,etc
Rigging form	Fixed
Data interconnection	CAT5 Cable ( L≤140m )； multi-mode fiber

Q:LED display power supply how to configure how many units with the plate is calculated.: I with 14 P10, power supply * (0.8-0.9) / each unit board power can be rounded down.

Q:What is the thickness of the led display?: The thickness of less than 75mm, with the aluminum. Can also be thinner but the material is not easy to find.

Q:What is the difference between an LED display and an LCD monitor?: Notebook LCD screen commonly used is TFT. TFT (Thin Film Transistor) refers to the thin film transistor, each of the liquid crystal pixels are integrated in the pixel behind the thin film transistor to drive, which can be high speed, high brightness, high contrast display screen information is the best One of the LCD color display devices is now the mainstream display device on laptops and desktops.

Q:LED electronic display and P have anything to do: P generally represents the pixel pitch, and P followed by the value of the two mainly refers to the distance between the pixels, usually called the point spacing. And the smaller the value of this point spacing, the higher the unit pixel, the more clear the display screen.

Q:LED display how to install it?: 1) single column installation: for small screen applications; 2) double column installation: suitable for large-screen applications; 3) closed maintenance channel: applicable to the use of the following columns: 1) single column installation: In the simple box; 4) open maintenance channel: for the standard box.

Q:LED display more than the size of the area must be 380v: General LED screen to reach more than 20 square meters will use more than two power lines, and then some will use three-phase electricity. At the same time and time-sharing power system with the use, so as not to impact on the power grid. The maximum power can take 80 percent of the capacity to leave a margin of 20 percent. Also pay attention to the choice of cable, and lightning protection measures.

Q:LED display a board dark light how is it?: What is the board? P10 There are three reasons for that. 1, first check the power on the line to the board on the line whether the soup or not connected! (Change line), 2, check the board above the terminal. (That is, to the board of the black plastic wire, a screw fixed line) that is and the board with welding wire welding. There may be no welding good. You can remove the outside kit. (Next to a small screw, unscrew on the line) to get a welding torch from the welding. 3, the original board on the Weld it Need to return to the factory new. The You said the board made dark may also be because the outside of the package drums appear perspective reflection. LED normal viewing angle is 70-110 degrees, the hope of the answer can help you

Q:Led display brightness is not enough because of what are the reasons: Display screen software which can adjust the brightness of the display. If you use the time for a long time, there are reasons for light failure, it is recommended to consider replacement

Q:How to identify the quality of led display quality: The thickness of the box of metal: the box is done with the manufacturers to do the structure of the drawings are related to the structure of the cabinet, the installation is easy, easy to install, the other heat will be better.

Q:Is the TV screen good for the LCD or the LCD?: Whether it is LED TV or LCD TV, their screen itself is LCD (LCD), the real LED display is difficult to use in the field of home TV, because its pixel is too large, high-resolution case is difficult The Now many of the store's dynamic billboard is LED dot matrix screen.

1. Manufacturer Overview
Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates
a) Certification Name
Range
Reference
Validity Period

3. Manufacturer Capability
a)Trade Capacity
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range