T5 LED Tube SMD Chip High Efficiency 0.6M 7W

Ref Price:
$5.65 / pc
Loading Port:
Payment Terms:
Min Order Qty:
10 Pcs pc
Supply Capability:
100000 Pcs Per Month pc/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

T5 LED Tube SMD Chip High Efficiency 0.6M 7W 1. This product meets the standard of CE certification.
2. With internal No-isolated power supply.
3. Round and the elliptical tube are available.
4. Use the most mature international well-known LEDSMD2836 as the light source, which can ensure the led tub܌챰;xǠ퐀

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:What does philips mean by TLD36w / 54-765
Yeah, I did it for you, I think it's the bottom, Let's see if it is ~ TLD ~ T8 Dailyght 160-240v (model) 36 ~ 36 w.I hope my answer will work for you.
Q:How does the traditional fluorescent tube stand install led lamp tube reforming method
Replace the lamp and rectifier with LED and matching. Traditional fluorescent lamp or low pressure mercury lamp, is using low pressure mercury vapor release ultraviolet ray after electricity, which makes the principle of phosphor emit visible light, so it belongs to low pressure arc discharge light source.
Q:20 square metre room application which led fluorescent lamp tube
The lamp tube can use 20w t8 1.2m LED light tube 6500k.I hope my answer is useful to you.
Q:How do you make the led lights like fluorescent lamps
A single led voltage current is 3v20mA, two and above 1.5 v batteries can be lit up, and a single small led with a 100 ohmic resistance can be plugged into a charging treasure.
Q:If the led lamp is replaced, the lamp power should be small
B: yes, half of it. 20w is much brighter than before.Yeah, how else to say energy efficiency.I hope my answer will work for you.
Q:Why don't leds and light bulbs adjust brightness by dimming switches
LED fluorescent lamp screen is the power supply failure in the lamp tube, the power transformer circuit has a problem. Fluorescent lamp flash screen. It may be that the regenerator is too long and the tube is too old to light up
Q:What happens to the daylight bulbs
This is your two wrong wiring, you switch control now is zero line didn't give disconnect the wire, so the light will flash, but it's nothing is short service life of some of the light.
Q:Why don't leds need a rectifier
Because LED is a direct current is needed to light, and the output voltage of rectifier is an alternating current, so can't use rectifier, now LED lamp is built-in power inside, and use it every time you'd better put fluorescent original rectifier and demolition of the starter, but given the easy to use, now LED lamp can be directly on the original fluorescent lamp holder, do not need to disconnect the rectifier, only need to send a link of the starter circuit cut. Because the regenerator will provide an instantaneous high voltage, it will damage the LED
Q:The child lamp chooses led good or the lamp tube is good
All can be LED with the natural white light bulb (osram), the lamp tube with three base color. From the protection of sight, try not to read for long periods of time, take a proper rest, look at the distance and move your eyes
Q:What is the connection of the LEDT5 lamp tube, the main line is how to connect, only to the end
1, the installation: The LED comes with a constant current source, which does not require a ballast and a regenerator. General T8 lamp tube because the lamp tube space is big enough, constant current source can be installed in the lamp tube. So, when installing, you can remove the ballast from the original frame and remove it, and install it directly. T5 fluorescent lamp, T4LED because tubes is very small, not put constant current source, can only be constant current source in a scaffold, so, T4 / T5 general manufacturers are doing, will deploy stents, stent in persistence current source, and the lamp installation direction of the. The direction is reversed, the lamp is not bright. We are considering adding some switching circuits to allow the lamp to work properly even if the lamp is in reverse. Voltage: to communicate 85V -- communicate 245V, all can work normally. However, the long-term voltage is too high or too low, which can affect the power factor of the constant current source, which means that the effect of energy saving will be slightly affected. At the same time, it can also affect the lifetime of the constant current. So, want to choose the fluorescent lamp that is appropriate voltage commonly.
We are a leading manufacturer of a broad range of LED strip light and LED Tube light. From 2011, we have integrating sphere spectrometer, high speed automatic placement machine, reflow soldering machine, automatic dispensing machines and other specialized equipment and professional R & D department. LED strip light can produce up to 300000 meters per month.

1. Manufacturer Overview

Location Shenzhen,China
Year Established 2011
Annual Output Value
Main Markets

Mid East;Western Europe
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port Shenzhen
Export Percentage
No.of Employees in Trade Department 20 People
Language Spoken: Chinese
b)Factory Information  
Factory Size: Above 4,000 square meters
No. of Production Lines About 5
Contract Manufacturing OEM Service Offered;Design Service Offered
Product Price Range Cheap