Straight Seam Welded Pipe Flat Head Chamfering Machine
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 set
- Supply Capability:
- 100 set/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
straight seam welded pipeflat head chamfering machine
Straight seam welded pipeflat head chamfering machine is used to crew cut the pipe end of straight seamwelded pipe or seamless steel pipe and finish the edges. Assisted with theprofile chamfering knife, the finished edges are homogeneous and beautiful. Itsadvantages are full auto working mode, high efficiency, and stable, reliableworking.
Specifications
1.The pipe make as customerized
2.used in the water pipe,gas,oil pipe
3.machine meet API-5L,GB9711.2 Standards
Spiral welded pipe flat head chamfering machine process:Loading pipe – connecting pipe – pinching – flat head chamfering – loosening the clamp – exiting the pipe
Spiral welded pipe flat head chamfering machine mainly is used to crew cut the pipe end of spiral welded pipe and finish the edges. The finished edges are homogeneous and beautiful.
The bearing type of spiral welded pipe flat head chamfering machine.
No
| Model
| Specification(mm)
| Length(m)
| Capacity(Kw)
| Area(M2) |
1 | ST-400 | Φ219~Φ426 | 6~12 | 70 | 5×23 |
2 | ST-650 | Φ219~Φ630
| 6~12 | 80 | 5×23 |
3 | ST-800 | Φ325~Φ820
| 6~12 | 60 | 5×23 |
4 | ST-1000 | Φ426~Φ1020
| 8~12 | 70 | 5×23 |
5 | ST-1400 | Φ508~Φ1420
| 8~12 | 90 | 5×23 |
6 | ST-1800 | Φ630~Φ1820
| 8~12 | 100 | 5×23 |
7 | ST-2400 | Φ720~Φ2400
| 8~12 | 150 | 5×23 |
8 | ST-3000 | Φ820~Φ3000
| 8~12 | 160 | 5×23 |
9 | ST-3500 | Φ1020~Φ3500
| 8~12 | 180 | 5×25 |
- Q: A roll forming machine, rolling out of the length is always not up to a fixed size, not too small, that is, more than that, what is the cause?
- According to my experience, there should be a problem with the boot encoder (also known as the digital wheel). Thank you. I hope I can help you.
- Q: What is rolling forming processing?
- Ironing the surface of the workpiece with a raised micro wave crest to fill the concave micro troughs, thus changing the distribution of the peaks on the surface, and obtaining smaller surface roughness values.
- Q: Improvement in rolling forming process
- The utility model has the advantages of short service life, easy damage and high comprehensive use cost.
- Q: Introduction of roll forming process
- With the progress of technology and the development of production, more and more attention has been paid to the roll forming process.
- Q: What kind of material and what heat treatment are used for pressing roller (molding, feeding, cutting force, heavy load, heavy load) of sheet steel rolling machine?
- Non bonding wear of rolled material (especially stainless steel strip, etc.)
- Q: What is the surface rolling forming machine process?
- Due to the rolling surface of metal plastic deformation, so that the surface microstructure of cold hardening and grain refinement, forming a dense fibrous, and the formation of residual stress, hardness and strength, so as to improve the surface wear resistance, corrosion resistance and compliance.
- Q: Process mould for rolling forming process
- Rolling forming is more complicated and requires higher than rolling thread. The die design is based on the different shapes of the workpiece, the design of the rolling plate into a cross section or a few sections, can use synchronous type; also can use grading type.
- Q: Material and equipment for roll forming process
- The most common type of roll forming is reciprocating flat wire twisting machine. Therefore, for the manufacturers of cold heading machines and screw rolling mills, the design of rolling dies is only a matter of design.
Send your message to us
Straight Seam Welded Pipe Flat Head Chamfering Machine
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 set
- Supply Capability:
- 100 set/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
