Semi-electric Stacker with Adjustable Fork--SPN1535-A/SPN1540-A

Ref Price:
Loading Port:
Shanghai
Payment Terms:
TT OR LC
Min Order Qty:
1 unit
Supply Capability:
1 unit/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

PRODUCT NAME:Semi-electric Stacker with Adjustable Fork--SPN1535-A/SPN1540-APRODUCT INTRO

 

ModelSPN1535-ASPN1540-A
Capacitykg15001500
Lifting heightmm75-350075-4000
Fork lengthmm1150
Load centermm400
Turning radiusmm2300
Outside width between legsmm1500
Inside width between legsmm1300
Outside width between forksmm190-800
Inside width between forksmm10-620
Lifting speedmm/s≥50
Lowering speedControllable
Lifting motor12v/1600w
Battery12v/100Ah
Charger220v/12v
Overall dimensionLengthmm1850
Widthmm1500
Heightmm22702520
WheelFront wheel diametermm100
Rear wheel diametermm200
Self weightkg550580

 

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:What standard elevator platform needs to go to the special equipment inspection to report
(the state council of the People's Republic of China on March 11, 2003 to no. 373 Based on January 24, 2009 the state council on amending the decision of the < > special equipment safety supervision regulations "amendment)
Q:How to use the elevator to be safer and more efficient
Annual maintenance Check all hydraulic pipes and connectors. The pipe shall not be broken, the joints shall not be loose, and all the joints must be tightened. Remove and disassemble the descending valve, blow the plunger through compressed air, then load and resettle. Remove the hydraulic oil, remove the oil strainer and remove the oil strainer, clean it up and then put it back in the tank. Be familiar with 'ten notices' 1, pay attention to the agencies should regularly check and adjust the brake of the brake and the clearance between the brake wheel, flexible and reliable. The clean surface, there should be no dirt, in case of dirt must wash with gasoline or thinners. 2, pay attention to removing the hydraulic tank of fuel cap, remove the cap around earth, unscrew the cap, remove residual impurities in the joint area (not rinse in order to avoid water seeping into the tank), confirmed to open the cap. 3, pay attention to the elevator remove the hydraulic tank of fuel cap, filter cover, test hole, hydraulic tubing parts, cause the system oil when exposed to avoid dust, remove the parts to open completely clear before first.
Q:How to automatically lift up and lift
The motor is controlled by a time relay, the motor is driven by a change of speed, and when it falls in place, it meets the power failure of the limit motor
Q:Which is good for mobile goods elevators?
Everyone knows that a penny a points goods, jinan economic brands cargo-lifts, although is not the lowest market price, but the interior of the lift platform all electronic components is a product of the military level,
Q:Which mobile shear fork lift is better
Mobile shear fork lift There are four major systems, The mechanical structure system,
Q:The tomb raider was not able to pry the gear in order
There are four of them, four of them. See the white climbing wall outside the elevator? Find a way to burst open a hole in the iron wire and climb to the fourth gear. There was no order in this gear, four of them were done, and the elevator fell down.
Q:Operation and attention of electric elevating platform car?
Non-professional personnel shall not adjust the overflow valve, the hydraulic system of each component is within the prescribed work under pressure, adjust the overflow valve, may lead to abnormal operation of hydraulic system. There are unnecessary injuries to people, machines and objects; Before any part of the hydraulic system, the pressure oil should be discharged before the pressure oil gusts out. E, the corresponding moving parts shall add some lubricating oil to extend the life of the bearing. F, check the oil and oil position of hydraulic oil. The platform rises all the way. In this position, the hydraulic oil should be 40-50mm above the bottom of the box. If the hydraulic press is dark, sticky or gravel, it is found that 120 # hydraulic oil should be replaced in time.
Q:Does the fixed hydraulic platform need to submit to the specification requirement
Lift platform, mobile elevators, cargo-lifts equipment, such as the regulations of the state, load is larger than 500 kg of belong to special equipment, is the need in the local quality supervision of special equipment inspection. First, look at the equipment capacity is over 500 kg, then you should go to the local quality inspection of special equipment department to put on record, first need information: including manufacturer's business license, tax registration certificate, organization code certificate, production license of special equipment, special equipment installation and maintenance license, there are different from region to region, it's best to make a phone call to prepare the material.
Q:What is the reason for the automatic lowering of the hydraulic platform
The hydraulic lift can rise steadily or maintain position because of the pressure oil in the cavity.
Q:What happens when the platform comes up and the power goes out.
Many platforms have an emergency drop.I hope my answer will help you.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range