Q:Which mobile shear fork lift is better

The mobile platform is a built-in power unit; The stationary elevator is usually an external power unit. You know that, you know how to compare it when you buy it

Q:The characteristics of hydraulic platform

Hydraulic lifts and elevators are both elevations, but the biggest difference is the journey. The advantage of hydraulic lift is smooth, especially in the initial end of the lifting, but again good hydraulic elevator also amounted to less than 10 m or a few meters, and the elevator is similar to hoist, well make up for the disadvantages.

Q:What is the phenomenon of the worker's transport of wood using a lift

The elevator is divided into the following mobile, fixed, wall, tractive, self-propelled, vehicular, and retractable seven categories: mobile The shear fork lift platform is a special equipment for high-altitude operation. The mechanical structure of it, make the lifting platform lifting has high stability, wide operating platform and high bearing capacity, larger, and the area of aerial work for many people work at the same time. Lifting power is divided into 24 v, 220 v or 380 v power supply, diesel engine, with Italy and domestic hydraulic pump station, mesa use antiskid insulated gusset plate, with non-slip, insulation, safety, please be assured that use.

Q:There are different kinds of milling machine and vertical lifting machine milling machine

Start by figuring out the difference between vertical and horizontal The main shaft of vertical milling machine is perpendicular to the workbench, and the spindle of horizontal milling machine is parallel to the workbench. The knife of vertical milling machine is relatively flexible, the scope is wider. Can use vertical milling cutter, machine clip, bit etc. Milling keyway, milling plane, boring hole, etc.

Q:How to improve the oil leakage line

The reason of oil leakage is complicated, mainly due to the quality of the hydraulic components, vibration, corrosion, differential pressure, pipeline connection, use of improper maintenance. Elevator oil leak inside leakage and leakage. A small amount of oil is inevitable, because of the nature of the hydraulic drive. Spill in excess of the prescribed index of the phenomenon is due to leakage, generally can immediately perceptible, mainly are now the pressure drops, rapid speed of change has been ground or surface of product oil, machine equipment need often fill oil to return to the height of the aerial work platform before. Once the leak is due to be shut down, the acute operation will only take the system out and damage the engine parts.

Q:Do you have a personal elevator with hydraulic platform

Hydraulic platform itself is not flat layer device, the upper and lower limit is oil cylinder and the mechanical structure limits. Platform only "motor" "stop" "up" "down" button. The safety of the sheared platform can also be shaken when it starts and stops, without the thought preparation. In different floor installed several travel switch, electric cabinet, become automatic stop, hardware does not need how many money, the line a little trouble. Can do it. Just installed is not good

Q:The automatic mahjong machine has a lift station always one. What is the other three normal

There are two main reasons for this: In the ascent of the aluminum plate, the interference with the limit mechanism

Q:How does the platform maintain

Remove and disassemble the valve, and remove the valve core and remove it from the new installation. Put all the hydraulic oil in the tank into the tank, remove the oil absorbent filter, and put it back in the tank. The oil tank refilled with new oil.

Q:Safety operation of hydraulic platform

Purpose: this procedure is used to guide operators to operate correctly and use hydraulic platform equipment. Two procedures: 1, the parts should be inspected carefully before they are work lifting platform, key check whether the screw connection is reliable, hydraulic pipe leaks, loose wires contact with and without, breakage, and so on and so forth. 2, lifting platform lift, put the leg in the four corners, four leg should be firmly supported on solid ground, dispatch work mesa to state level (visual). Turn on the power, the indicator should be on. Then start the motor, pump work, drop one or two in the air, check the parts and then start working again. When the temperature is below 10 ℃, should make the pump running 3-5 minutes, confirmation of oil pump work can be carried out. 3, homework personnel enter the platform after the guardrail doors should be closed, with bolt, tied on safety rope, the center of the load (people stand location) should be in the center position of workbench face.

Q:The design of graduation is designed for mobile shearing and hydraulic lift

Aluminum alloy lift, lift platform aluminum, aluminum alloy lift platform, aluminum alloy elevator, shear fork lifter, cut shear fork lifts, the fork lifts, elevator guide rail type, guide rail type cargo-lifts, set of cylinder type elevator, set of cylinder type lift table, set of cylinder type elevator, fork lift platform, guide rail type lift platform, set of cylinder lifting platform, electric lift high quality manufacturer, welcome new and old customers to choose