Mineral Fiber Ceiling with Texture MA03

Ref Price:
Loading Port:
China Main Port
Payment Terms:
Min Order Qty:
Supply Capability:

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Typical Application Areas:

Hotel Lobbies and Corridors

Offices and conference rooms


Hospitals and other Public Site

Department stores

Super Malls

Technical Data:

Density (kgs/m3): 240-280kgs/m3

NRC: ≥0.45

Fire resistance: class a qualification(GB8625-88 STIPULATION)

Moisture rate (%): ≤3

Light reflect: 0.60-0.80

Bending strength(N): ≥60

Sagging resistant properties:≤0.35mm

HR: ≥90%

Main Advantages:

High humidity resistance properties

Excellent light reflectance


Wonderful sound-absorption

No content of asbestos

Zero release of CH2O

Economical Choice

Available Textures:

Astral Series: MA01, MA02, MA03, MA04

Perforated Series: MP01, MP02, MP03

Fissured Series: MF01, MF02

Sand Series: MS01, MS02

Customized textures are also welcome ifbuyer pays for new-mould charges.

Standard Size:

2’X2’; 595mm*595mm;

2’x4’; 1195mm*1195mm;

Thickness Range: 6mm – 15mm

Edge Detail:

Square edge for 15mm & 24mmT-Grid

Tegular edge for 15mm & 24mmT-Grid

Micro-lock tegular edge for 15mm T-Grid

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:What is the industry like this?
This decorative material for the South, and the high price, but the prospects are good, there is development value, to seek some high-end users, there is a certain harvest. The north side has not been developed, but some people in use. The effect is good, in short, a little 'high-end'
Q:Asbestos? Mold? Or just old insulation?
If your house is newer than 1980, there is virtually no chance of it being asbestos. Get into the 70s and older and there starts to be some doubt. It could also be mineral wool. Mineral wool installs and behaves like fiberglass, except it's made from, if I recall correctly, foundry slag that has been blown into fibers a bit like cotton candy. Fiberglass insulation is generally pink or murky yellow, but mineral wool is usually gray. Use the same precautions with it as you'd use for fiberglass and you should be fine. Blown in insulation is usually cellulose. A mask should be all you need with it. If you are in any doubt, call a pro. Getting the material tested so you can be sure won't set you back too much, and it's a hell of a lot cheaper than needing to talk to a pulmonary specialist.
Q:Uv decorative board is what?
The so-called uv decorative plate, which refers to its surface after UV curing paint protection treatment of a new environmentally friendly decorative materials, its substrate contains cement pressure board, solid wood multilayer board, MDF, glass magnesium fire board four. Uv decorative plate surface after a special treatment more smooth and smooth, wear resistant, resistant to corrosion, heat and cold, excellent performance, very popular in the market.
Q:What are the disadvantages of polymer UV decorative panels?
Polymer plate in a lot of years ago have a similar product, after the gradual upgrading of technology, building materials used in general is the plastic polymer, the fire performance is a never hide the problem, which makes it in many large places , The public environment and even the use of home improvement will be limited, but also consumers need to pay attention to the place of purchase.
Q:Does the decorative board need to paint a layer of paint?
Construction technology measures: 5.1 find and play line: wood wall panels should be installed according to the design Atlas requirements, in advance to find a good elevation, flat position, vertical size of the elastic line. 5.2 Check the embedded parts and holes: After the bumper line to check whether the embedded parts, wood bricks or wooden wedge meet the design requirements, spacing spacing size, position to meet the requirements of the lapel keel; measuring doors and windows and the location of the size of the vertical And design requirements are consistent. 5.3 shop, coated with moisture-proof layer: the design of moisture-proof requirements when the wooden wall, wood keel installation must find a square, looking straight, skeleton and wood between the gap should be pad mats, each brick at least 2 nails nail, And then put the keel should be set aside when the board thickness. Wood keel and wall contact surface to be anti-corrosion treatment, the remaining three sides of not less than three times the treatment of fire paint. 5.4 Lining installation: After the installation of the keel to check the qualified installation of 15mm thick woodworking board to do lining, requiring liner nail firm, nail fixed spacing control in 200mm or so, the back brush fire paint, splicing board should be reserved between the 5mm Around the expansion of the gap, to ensure that the amount of expansion and contraction of temperature.
Q:PVC crust foam board, cabinet board, decorative board (inkjet processing) need to do 3C certification?
Do not belong to the 3C certification directory do not need to do 3C certification.
Q:Old paragraph Han Lanta front cover stone decoration board
Only the installation of the decorative cover is not in place and the control station gap is too large, hoping to help you, hope to adopt
Q:Car a column decorative plate how to dismantle
No need to remove, the edge of a little hard to break apart, can put the line into it.
Q:Microcrystalline stone uv decorative plate with no radiation
Production of microcrystalline stone recommended Toshiba uv printer, which uses a Toshiba nozzle, ink point for the 5PL, print speed faster than Epson 2 times, print accuracy than Ricoh's high life in 24 months to 36 months, There are also 2 years warranty.
Q:How to protect the insulation board to play the greatest insulation effect?
External wall insulation system should consider the fixed parts, supporting the thermal bridge on the impact of thermal insulation decorative board construction should deal with hot and cold bridge parts - the wall should do insulation decorative plate seal waterproof structure design to ensure that water infiltration insulation layer and grass level; level or tilt Picking parts and extension to the surface should be done waterproofing external wall insulation system installation equipment or pipe should be fixed with the grass-roots and sealed waterproof design

1. Manufacturer Overview

Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range