Standard Size: 595mm*595mm, 605mm*605mm
Standard Thickness: 9, 10, 12, 14, 15, 18mm
Edge Detail: Square Edge, Tegular Edge (≥12mm)
Technical Data of Mineral Fiber Ceiling:
Fire resistance: Class B1 (standard GB 8624-1997)
Moisture rate (%): ≤3.5 (40℃,70%RH)
Light reflect: 0.70-0.80
Sagging resistant properties: ≤0.35mm
Humidity Resistance: ≥85%
Typical Application Areas of Mineral Fiber Ceiling:
Hotel Lobbies and Corridors
Offices and conference rooms
Hospitals and other Public areas
- Q:Will "plastic decorative panels" can paint to change color?
- Can change color, the general car surrounded by itself is plastic.
- Q:Ling Du car under the chassis before the plastic decorative plate damage how to repair
- Can go to repair the factory. The punching is fixed with a tie. Or glue glue. Or replacement. According to the degree of damage. I wish you a happy car
- Q:Plastic decorative plate of plastic decorative plate of raw materials
- Surface paper is placed on the top of the decorative plate, impregnated resin and hot pressing, with a high degree of transparency and hard, play a protective decorative plate surface role. This paper is thin, white, clean, and has a high absorption performance.
The bottom of the paper used to make the decorative plate of the substrate, so that the plate has a certain thickness and strength, is to create an important material decorative plate, 80% of the amount of paper, the paper content of low ash, requires a higher absorption performance and Wet strength. Commonly used non-waterproof agent of kraft paper for its base paper.
- Q:retrofit insulation for walls?
- I saw on This Old House when they blew in cellulose insulation from the outside. They drilled a hole about 2 feet from the floor level and another hole about 2 feet from ceiling level. They blew it in starting at the bottom until they saw the cellulose start to blow out the top hole. Then went to the top hole and blew it in until they heard the machine whine meaning it couldnt push anymore. The purpose with 2 holes was to make sure the whole cavity was filled. In your case you can take off one piece of siding for each stud cavity if its vertical siding or take off two rows at the correct heights. (That is if you have plywood/osb on the outside). The spray foam will just be too hard to fill correctly without taking down the sheetrock.
- Q:What is the cabinet of the decorative plate
- Decorative board should be the cabinet door, paint, blister, UV grain gold and so on some of the columns of the decorative door
- Q:Novice neighborhoods (woodworking board and surface decoration board is how to stick together)
- Large area of hand paste very few can persist for 2 years, will be bubbling. There is a good way I used to: the use of good quality white latex, both sides are brush evenly, put all the board stacked well, with a card or applied to the weight (I use the weight of the iron scale ), 5 days after the line, much better than Wan Nengjiao. In short a word, the whole brush to the full pressure of the strict, the plastic are squeezed out on the line.
- Q:Which brand of color stainless steel decorative plate quality to do better?
- Oregon brand it, they have a large PVD vacuum ion plating equipment and technology, the main processing production of high-grade color stainless steel decorative panels
- Q:Uv board directly with glue on the tile up line
- Installed with wall glue
1, in the wall covered with a grassroots level, commonly used is 3MM plywood, woodworking board, a good point is the fire glass magnesium board. With nails to nail them on the wall, and with a sandpaper to clean the board.
2, saw the board, the UV decorative panels according to the actual requirements of a block into a block.
3, the edge, will be installed on the four sides of the UV board with a chamfering machine down to 45 degrees angle. According to the actual installation requirements, and some just down the next two sides or three sides.
4, clean the back of the UV board, with a sandpaper and rag to clean the back of the UV board.
5, the Wan Nengjiao or wood glue evenly coated on the back of the UV decorative panels, and then flatten the UV decorative plate on the wall, and then gently hammered the UV decorative panels, so that the UV decorative board more firmly stick to the wall The
6, water transfer joints, and then fill in the two pieces of UV decorative plate 45 degrees angle intersection, first filled, and then the vertical angle of wood from the 45-degree angle at the intersection of gently across, so that the intersection It is beautiful.
- Q:Is the floor of the bedroom good or the floor is good?
- Wood flooring by the weather and moderate impact of large, easy to deformation after flooding Alice; need regular waxing maintenance; easy to be sharp objects scratched; composite wood flooring and formaldehyde release; compared to tile wood flooring shorter life The
- Q:Anti-static stone-free composite decorative panels
- The middle of the decorative plate is made of wood or stone decorative layer, the upper and the bottom two layers of unsaturated polyester resin composite layer. It has the characteristics of oil, water resistance, acid resistance, alkali resistance, corrosion resistance, high temperature resistance, flame retardant, bright as mirror and so on. The pattern pattern is arbitrarily selected and the size is arbitrarily determined, and the thickness is between 0.2 and 3mm. Can be thick up to 5mm, the surface strength is high, the overall toughness is good, thin can be rolled into a tube, widely used inside and outside the walls, floors, ceiling ceiling, furniture, wood, billboards, painting plaque and other decoration. Sales price of 20-90 yuan / square meter
SERENITY,is a large company which produces light mineral wool acoustic board. It displays a good combination of production , manufacture, supporting sales and international trade.Its products cover more than twenty varieties of six categories, including knurling board, relief-embossing board, printing board, spraying board, stereo-molding board, etc.
1. Manufacturer Overview
|Annual Output Value
||US$5 Million - US$10 Million
||Japan, Italy, South- Africa ,India, Russia, Malaysia, Singapore, Taiwan and other countries and areas
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
||61% - 70%
|No.of Employees in Trade Department
||30,000-50,000 square meters
|No. of Production Lines
||OEM Service Offered Design Service Offered Buyer Label Offered
|Product Price Range