High Speed Slitting and Cut to Length Line-1
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
General Information：
High speedslitting and cut to length can cut steel with thickness from 1mmto 16mm, if noneed slitting thickness up to 30mm.
Sandwichpanel, as a new building material，shows excellent performance oninsulation. We can design the line to make different kinds of panels inappearance, for wall panel and roofing panel with various joint designs.
It is takingthe place of brick to be a main material for building now.
Processing flow is as following:
Carry coil→loadcoil→de-coiling（pressingguide +opener）→entry、roughlevel→cutting→transition→guide→slitting (waste winding) →loopingstorage→pre-separating, damping→recoiling→packing→discharging→guide→leveling→fix size (end platefeeding)→cutting→discharging
Technical Data：
1. Coil Thickness：0.3-4mm
2. Coil Width：300-1800mm
3. Coil Max. Weight：30 T
4. Coil I D：φ508-φ800mm
5. Material: carbon steel platewith σb≤550Mpa、σs≤350Mpa
- Q: Slitting machine; batten; place
- We must first ensure that the metal slitting machine test machine operator familiar with the operation process, and in strict accordance with the operation, and has the qualification. This includes the operator itself can not stay long hair, wearing a glove machine, clothes to the cuff tightly (handling tool except) is to ensure the operator is divided. A machine in the operation of metal safety.
- Q: There is a gap in the size of the strip machine, and the material is burr. Is the cutter axis beating or something else? How do you solve it?
- The photoelectric proximity switch on the top photoelectric proximity switch or buffer pit at the top of the opener is damaged, and the silicon steel sheet can not be detected near the signal and should be replaced.
- Q: Why does a bar break occur in a bar splitting machine?
- The uneven gap between the upper and lower blade produces bending: when the left and right gap is larger, the part of the impression is larger than the left and right side of the gap, so it shows a great curvature
- Q: The technique of arranging knives in a slitting machine
- Fixed length slitting control is divided into two types: static and dynamic cutting.
- Q: Slitting machine, slitting machine looper (pit cause analysis) in the strip of varying lengths
- The tension of the tension mechanism is uneven, and the tension of the tension mechanism is big. Small matters determine the tightness of the take-up volume, and the outer diameter of the take-up strip with a large tension is smaller, otherwise it is large. The take-up speed of the coil with big outer diameter is larger.
- Q: Slitting machine, pc0.8 mm coil, why have rough edges?
- Improper use of winding and winding motor series. Fast series of changing motor.
- Q: How to adjust the pearl cotton separator?
- Adjust the conveyor belt, arbitrary adjustment of one, so that the pearl cotton tape machine with the film roll paper side of the drilling alignment;
- Q: What is the relationship between the arrangement of metal bars and the material thickness of the strips?
- The width of the material determines the size of the separator, but the thickness is related to the configuration of the metal separator
- Q: How is the gap between the cutter and the cutter in the metal slitting machine measured without damaging the knife?
- One is single-sided corrugated machine, first made of single-sided corrugated cardboard, and then through a single glue car processing, made into different structures and corrugated cardboard.
- Q: Is the tape on the tape slitting machine a good one at the back or a good one in front?
- If you are concerned about the volume from the front. Mainly depends on your mother roll size, whether to change regularly, the quality of mother roll, how about, do not pay attention to its condition. Very few people ask this, I may not consider the full, you have the right to reference!
Send your message to us
High Speed Slitting and Cut to Length Line-1
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
