High Speed Slitting and Cut to Length Line-2

Ref Price:
Loading Port:
Tianjin
Payment Terms:
TT OR LC
Min Order Qty:
-
Supply Capability:
-

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

General Information

High speedslitting and cut to length can cut steel with thickness from 1mmto 16mm, if noneed slitting thickness up to 30mm.

Sandwichpanel, as a new building materialshows excellent performance oninsulation. We can design the line to make different kinds of panels inappearance, for wall panel and roofing panel with various joint designs.

It is takingthe place of brick to be a main material for building now.

Processing flow is as following:

Carry coil→loadcoil→de-coiling(pressingguide +opener)→entry、roughlevel→cutting→transition→guide→slitting (waste winding) →loopingstorage→pre-separating, damping→recoiling→packing→discharging→guide→leveling→fix size (end platefeeding)→cutting→discharging

Technical Data

1.  Coil Thickness:0.3-4mm

2.  Coil Width:300-1800mm

3.  Coil Max. Weight:30 T

4.  Coil I D:φ508-φ800mm

5.  Material: carbon steel platewith σb≤550Mpa、σs≤350Mpa


Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:There is a gap in the size of the strip machine, and the material is burr. Is the cutter axis beating or something else? How do you solve it?
The photoelectric proximity switch on the top photoelectric proximity switch or buffer pit at the top of the opener is damaged, and the silicon steel sheet can not be detected near the signal and should be replaced.
Q:Slitting machine; batten; place
When feeding should pay attention to the unloading arm pulley to kill, to prevent the unloading arm and the winding shaft from the material off injured foot.
Q:Is the tape on the tape slitting machine a good one at the back or a good one in front?
If you are concerned about the volume from the front. Mainly depends on your mother roll size, whether to change regularly, the quality of mother roll, how about, do not pay attention to its condition. Very few people ask this, I may not consider the full, you have the right to reference!
Q:Slitting machine, pc0.8 mm coil, why have rough edges?
See if your device's line speed matches previous settings. Is it online faster?. In the past, the torque was gained by changing the coiling moment motor.
Q:What is the difference between a slitter and a slitter?
It is a kind of mechanical equipment used to cut wide width paper or thin film into many narrow materials. It is commonly used in paper making machinery and printing and packing machinery.Before the cutting machine of magnetic powder clutch speed is not high, because of high speed friction, in operation due to the magnetic powder to produce high temperature, shorten its service life, serious when the death card, make the machine run suffocate suffocate, bring very serious consequences for the production. Seriously affected production efficiency.
Q:The belt machine used for gluing buckles lacks power
The main reason is that the ignition advance angle is incorrect, the fuel pressure is too low, the intake system leaks, the throttle position sensor or air flow meter fails, the injector is not working well, and the EGR system is not working well.
Q:Why does a bar break occur in a bar splitting machine?
As a result of burr and bending: vertical cut due to the blade gap adjustment is not correct, so that the burr larger, when the volume of the edge due to burr, equivalent to the larger thickness of the plate, resulting in edge stretching and bending.
Q:How is the gap between the cutter and the cutter in the metal slitting machine measured without damaging the knife?
One is single-sided corrugated machine, first made of single-sided corrugated cardboard, and then through a single glue car processing, made into different structures and corrugated cardboard.
Q:What is a striping machine?
The first row of specifications is full size 580, second specifications (550+8+1.8), the lower is the first (550+8+1.8), the second is 580, 20, the two sides cut specification good flank is outwards, full size two good knife face.
Q:What is the difference between CNC slitting machine and slitting machine?
Reasonable layout, convenient operation, high automation, high production efficiency, high precision work, all kinds of sheet metal processing various cold-rolled, hot-rolled coil, silicon steel plate, stainless steel plate, color plate, aluminum plate and after the plating coating or.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range