Specification

1.  Features & Benefits
  - Package: 2.8*3.5*0.65mm (Top view white LED)
  - Emitted Color: White
  - Soldering methods: All SMT assembly methods
  - Enables 3-, 4-, 5-step MacAdam ellipse kits
  - Extremely wide viewing angle，standard form factor design flexibility
  The minimum luminous efficiency 160lm/w@60mA
2. Typical Application:
  - Bulb                                                                        
  -  ndoor & Outdoor sign board back light
  - Advertising backlighting
  - General use.

3. Precautions for use
    3.1 Soldering
   SMD LED encapsulation is very flexible, outside force easily demolish radiant surface and plastic, As soldering , Please handle with care!
     a.  With No-clean Flux, according to reflow soldering cure condition when soldering, Reflow soldering should not be done more than two times, simultaneity you must insure clean on the radiant surface. Otherwise, foreign objects can affect radiant color. 
     b.  Don’t process manual soldering except repair. Recommended to be soldered with 25W Anti-static iron, The temp. of the iron should be lower than 300℃  and soldering time should not be done more than three seconds, at the same time iron can’t touch radiant surface and plastic. 
     c.  Don’t twist LED in course of manual soldering and experiment, Otherwise, the lights will not work possibly.
     d.  Please use the same BIN grade in one panel, and don’t mix the difference BIN grade in one panel when soldering. Otherwise, it will cause a serious uneven color problem.
     e.  Please control the sulfur content of solder paste and PCB.
     f.  Pb-free solder temp.-time profile as below:260℃Max.

     3.2  Cleaning
     a.  Don’t be cleaned with ultrasonic. Recommended to be wiped with isopropyl alcohol or pure alcohol,wiping time should not be more than one minute. LED must be placed at room temperature for fifteen minutes before producing .you must insure clean on the radiant surface. Otherwise, foreign objects can affect radiant color.
     b.  LED can’t be in contact with acetate、 trichloroethylene， acetone、 sulfur、 nitride、 acid、 alkali、 salt. These matters can destroy LED.
   3.3 Sealing
     a.  Sealing glue can’t contain sulfur，because these matter can affect fluorescence powder poisoning.
     b.  When using normal sealing glue, recommended will be operated life for 168hrs under normal temperature.
    3.4 Storage
     a.  Don’t open the moisture proof bag before ready to use the LEDs.
     b.  The LEDs should be kept at  30℃  or less and 60%RH or less before opening the package. The max. period before opening the package is 1 year.     c.  After opening the package, the LEDs should be kept at 30-35%RH or less, and it should be used within 3 days. If the LEDs should be kept at 30-35%RH or more, and it should be used within 4 hours.
     d.  If  the  LEDs  be  kept  over  the  conditions  of  20%,  baking  is  required  before  mounting.  Baking condition as below: 70±5℃  for 12 hours for bulk goods, 105±5℃  for 1 hours for roll goods.
     e.  The environment have no acid、alkali、corrosive gas、intensively shake and high magnetic field.

    3.5 Test
     a.  Customer must apply the current limiting resistor in the circuit so as to drive the LEDs within the rated current. Otherwise slight voltage shift maybe will cause big current change and burn out will happen.
     b.  Also, caution should be taken not to overload the LEDs with instantaneous high voltage at the turning ON and OFF of the circuit.

      c. The reverse voltage mustn’t exceed 5v when lighting on or testing the LED, otherwise, LEDs will be damaged.