HG114 Pipe Makingf Machine
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- 10 sets set/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
The mill is intended for manufacturing round pipe of Φ50mm-Φ114mm with thickness of 1.5mm–5.0mm from cold-rolled and hot-rolled coil strip by means of unclosed tubular blank with its subsequent welding into tube, edge heating by means of solid state high-frequency welder, longitudinal seam welding in rolls of tube welding machine, cooling, further sizing or shaping and on-stream cutting of endless tube in measured lengths.
Finished product will be of round, square or rectangular pipe.
The manufacturing process provides for the uses of coiled strip precut in required width sizes in slitting machine.
II. The technical flow of the production line
{SteelTape}→→ Double-head un-coiler →→Strip-head Cutter and welder→→
Horizontal spiral accumulater →→Forming section(Flattening unit +Main driving unit +Forming unit +Guide unit +High frequency induction welding unit +squeeze roller)+ De-burr frame →→Cooling unit →→ Sizing unit and straightener →→Flying saw under computer-control →→ Run-out table
III. Basic conditions:
a) Steel Pipe Specification
1. Round Pipe diameter: Φ50 –Φ114mm
Pipe Thickness: 1.5 – 5.0mm
2. Square & Rectangle Pipe: 40X40mm –90X90mm
Pipe Thickness: 1.5 – 4.0mm
3. Pipe Length: 6.0m – 12.0m
4. Length Tolerance: 0-6mm
b) SteelTape Specification
1. Material: Carbon steel (δb≤500Mpa, δs≤235Mpa)
2. Steel Tape: Inner diameter: Φ470-510mm
Outer diameter: Φmax=1800mm
Strip steel width: 160mm-400mm
Strip steel thickness: 1.5mm-5.0mm
The maximum weight: 4.0 tons
c) Electric installed capacity: appro. 800KW
d) Size of the whole line: appro. 75X7.0m
e) Line Speed: 20-70m/min
Forming & sizing section
4.1 Forming mill gearbox, universal joint
4.1.1 Mill entry flattener by up-horizontal roll and below-horizontal roll, one positive five-roll flattener, one pair of feeding vertical roll.
4.1.2 Forming mill consists of:
- Driven stand: 7 sets (Horizontal)
- Driven stand shaft: Φ 100mm
- Material of shaft: 40Cr
- Side roll stand: 8 sets(Vertical)
- Side roll stand shaft: Φ60mm
- Material of shaft: 40Cr
- Gear box & universal joint: 7sets
- Material of gear box: cast steel
- Material of gear: 20CrMnTi
- Main motor: 132kW Model: Z4-250-31 1 set
- Main redactor: 1 set
- Horizontal roller frame with worm gear & shaft. adjust up and down at same time and level.
4.2 Sizing mill gear box, universal joint
4.2.1 Sizing mill consist of:
- Driven stand: 5 sets (Horizontal)
- Driven stand shaft: Φ 100mm
- Material of shaft: 40Cr
- Side roll stand: 5 sets (Vertical)
- Side roll stand shaft: Φ60mm
- Material of shaft: 40Cr
- Gear box & universal joint: 5 sets
- Material of gear box: cast steel
- Material of gear: 20CrMnTi
- Main motor: 110kW Model: Z4-250-11 1 set
- Main redactor: 1 set
- 2 set single head Turk’s head, with 4 rollers*2sets
- One speed testing roller with air cylinder for CNC flying saw
- Horizontal roller frame with worm gear & shaft. adjust up and down at same time and level.
- Q:How does the pipe machine operate?
- Site equipment must have a professional engineer to manage the responsibility, every day to the equipment under the jurisdiction of not less than 2 times inspection; maintenance personnel for the jurisdiction of the production equipment to do not less than 4 times the inspection work; for production
- Q:What is the difference between galvanized welded steel pipe and galvanized steel pipe?
- Welded black tube through the surface treatment, removal of pipe surface oxide and other debris, can increase the adhesion of galvanized layer in the tube matrix.
- Q:What kind of plastic pipe is divided?
- There are thermoplastic PVC pipe, polyethylene pipe, polypropylene pipe, poly-formaldehyde pipe, ultra-high molecular weight polyethylene pipe; are thermosetting phenol plastic pipe.
- Q:Cement pipe machinery and equipment how to work?
- Rotate, then start the feeder from one end of the mold to the other end of the feed, when the concrete is higher than the mold ring 3-5mm, the concrete directly with the spindle contact, relying on the weight of the mold and the weight of concrete compaction reinforced concrete drainage pipe
- Q:The introduction of the pipe machine is
- As a result of stainless steel pipe forming, welding technology is mature, in many areas has replaced the seamless tube.
- Q:What is the purpose of each mold of stainless steel pipe machine?
- Stainless steel tube molds use: not only can produce regular stainless steel tube, stainless steel square tube can also produce all kinds of special-shaped tube, such as plum tube, fan tube, oval tube and so on.
- Q:What is the stainless steel pipe machine?
- The most common is the circular and square rectangular tube, all square rectangular tube is made by the tube, because the last few sets of molds can make the tube into a rectangular tube.
- Q:Pipe machine on the bearing what are the requirements
- Equipment with length control device, the next chat length can be set according to their own requirements, can effectively reduce the loss of material head.
1. Manufacturer Overview |
|
|---|---|
| Location | |
| Year Established | |
| Annual Output Value | |
| Main Markets | |
| Company Certifications | |
2. Manufacturer Certificates |
|
|---|---|
| a) Certification Name | |
| Range | |
| Reference | |
| Validity Period | |
3. Manufacturer Capability |
|
|---|---|
| a)Trade Capacity | |
| Nearest Port | |
| Export Percentage | |
| No.of Employees in Trade Department | |
| Language Spoken: | |
| b)Factory Information | |
| Factory Size: | |
| No. of Production Lines | |
| Contract Manufacturing | |
| Product Price Range | |
Send your message to us
HG114 Pipe Makingf Machine
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- 10 sets set/month
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Related keywords
