Diesel Forklift 3.0t with Japanese Engine
Load Capacity:1T - 5T
Fuel Tank Capacity:50L
Length to Fork Face:2780mm
Travel Speed.with/Without Load:0-20km/H
Lifting Speed,with/Without Load:450/470mm/S
Reasonably low-center gravity design:By computer digital imitation,the most suitable and stable low center of gravity is designde. At the same time, body is weld by high intensity steel plate, assuring forklift being more stable and safe in traveling.
Double-"J"high rigidty mast material and intelligent system of downing and buffering.
Wider and more comfortable seat.
Tilt-adjustable steering wheel.
Human-based hydraulic steering-handle
Super elastic solid tire
Shock absorption system
|5||Full free lift height||mm||135|
|7||Mast tilting angle||Front/Rear||Deg.||6/12|
|8||Min. turning radius||mm||2470|
|9||Min. width of right angle|
|10||Min. width of right|
|12||Overhead guard height||mm||2120|
|14||Performance||Max. travel speed||Full load||km/h||19|
|15||Max. lift speed||Full load||mm/s||460|
|16||Max. traction power||Full load||KN||20|
|Dimensions||Total length||With fork||mm||3805|
|18||Total length||Without fork||mm||2735|
|20||Mast extended height||mm||4265|
|21||Mast lowered height||mm||2040|
|28||Motor||Model ||ISUZU C240|
|30||Rated torque ||N.m/r.p.m||137.7/1800|
|33||Fuel tank capacity||L||70|
|35||Operating pressure ||Mpa||18.5|
- Q:Can a forklift get on the highway?
- Where did you say the road was? The average car can go on the highway, the highway is not good, the speed minimum 90 you that forklift drive up?
- Q:The basics of driving a forklift
- When uninstalling, it is strictly forbidden to unload the plates, turn the pan or use "archery" to avoid damaging the fork. The strict execution of the "five non-fork" in the job: the center of load of the center of mass of the cargo over the fork. A single fork is not a fork when it is carried; Cargo stacking without a fork; A fork may damage the cargo without a fork. Exceed the nominal load of the forklift or the quality of the cargo. When the goods are easily broken, valuables or loaded with unstable goods, or when the goods exceed the height of the portal, the safety ropes shall be bound and the special persons shall be guided when necessary. When two forklifts unload the same cargo at the same time, they should be in contact. When taking the goods at the platform, the fork can only be taken from the platform. There should be some safety precautions when crossing the cross.
- Q:The advantages and disadvantages of exhaust and exhaust in the forklift truck
- Agree upstairs, if not to seek professional technical personnel.I hope my answer will help you
- Q:Where can I get a forklift
- If you want to learn forklift, I can recommend a good forklift school, in dongcheng, dongguan experimental mechanic school, which is assigned. Very good!
- Q:What's the matter with forklift
- Forklift, electric forklift in the process of driving, sometimes will appear to the phenomenon of heavy hard, very is to make the forklift driver have a headache, what reason is caused by the forklift steering failure? Here are five reasons for the failure: (1) horizontal pull rod, steering bridge bending deformation, or whether tire pressure is adequate.
- Q:Forklift, forklift, loader, which is a special equipment
- The forklift truck is also included in the special motor vehicles in the present (factory) The loading machine is no longer the case. It is in the safety board. The eight categories under the special equipment safety supervision ordinance.
- Q:What is the difference between the series of internal combustion forklifts
- Computer overheating will and life has a great influence on the performance of the whole machine, so the daily maintenance and maintenance may maintain the good performance of the computer and the extension of service life, also should keep good habits.
- Q:The scope of the forklift truck
- Available on the market of forklift brand is numerous, complex models, together with the product itself technology is strong and very professional, so the choice of models, such as the supplier of choice is a lot of choose and buy of enterprises often face the problem. This paper mainly introduces the selection of car, brand selection, performance evaluation criteria and the contribution rate of Chinese forklift truck overseas. "Special equipment safety supervision regulations" article 38: "boiler, pressure vessel, elevator, lifting machinery, passenger ropeway, large-scale amusement facilities, field (factory) the operator of the special motor vehicles and related management personnel, shall be in accordance with the relevant provisions of the state by the special equipment safety supervision and management department of examination qualified, obtains the national unified format of the special operations personnel certificate, shall not engage in the corresponding operations or management."
- Q:The forklift card has been tried for several years
- Forklift driving license (forklift license) is issued by the state production safety supervision and administration of the People's Republic of China special operations card ", forklift only used in the unit within the work place.
- Q:The operation procedure of forklift truck
- (4) loading and unloading (1) fork materials, should according to need to adjust the distance between two goods fork, make the two forks load balancing, not skewed, items side should be posted on the shelves, fork in weight shall comply with the provisions of the curve of load center sign. (2) the carrying capacity shall not obstruct the sight of the driver. In the course of loading and unloading, the brake forklift must be used. (4) when the goods are approaching or exiting the goods, the speed should be slow and steady, and the wheel should not be rolled over the items, wooden pads, etc., so as not to be crushed by the roller. (5) when taking goods with a fork and fork, the cargo fork should be as deep as possible in the load, and the tip of the fork cannot touch any other goods or objects. The minimum door frame should be used to stabilize the load, so the load will not slide backward. When the load is put down, the door is small enough to allow the load and the fork to be drawn. (6) the high speed forked goods and the collision between the fork and the hard object are prohibited.
1. Manufacturer Overview
|Annual Output Value
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
|No.of Employees in Trade Department
|No. of Production Lines
|Product Price Range