Butterfly Valve Stainless Steel Threaded Directional Made in China on Sale

Ref Price:
Loading Port:
Payment Terms:
TT or LC
Min Order Qty:
100 pc
Supply Capability:
10000 pc/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:


1. Manual Wafer Butterfly Valve Description

A butterfly valve is a valve which can be used for isolating or regulating flow. The closing mechanism takes the form of a disk. Operation is similar to that of a ball valve, which allows for quick shut off. Butterfly valves are generally favored because they are lower in cost to other valve designs as well as being lighter in weight, meaning less support is required. The disc is positioned in the center of the pipe, passing through the disc is a rod connected to an actuator on the outside of the valve. Rotating the actuator turns the disc either parallel or perpendicular to the flow. Unlike a ball valve, the disc is always present within the flow, therefore a pressure drop is always induced in the flow, regardless of valve position.


2.Main Features of the Manual Wafer Butterfly Valve 

a)Cast hole. Flange connection meet ANSI 125/150#   DIN PN10/16   BS4504 PN10/16 in the meanwhile.


b)Soft seat. Replaceable. Increase of service life.


c)Double half shaft without pin.


d) Square and short neck. Easy to stick scutcheon and cost saving.


3. Manual Wafer Butterfly Valve Images


Butterfly Valve Stainless Steel Threaded Directional Made in China on Sale

Butterfly Valve Stainless Steel Threaded Directional Made in China on Sale


4.Manual Wafer Butterfly Valve  Specification



Butterfly Valve Stainless Steel Threaded Directional Made in China on Sale 



1. What is manual wafer butterfly valve?

A: Wafer style is the more common of the two and is less expensive than the lug style. The wafer style butterfly valve is just about the standard. It ís so common that no one even bothers to use the word "wafer" when ordering a butterfly valve. It is taken for granted that if a butterfly valve is ordered, a wafer style will be received.


2. How about the Installation of the Wafer Style Butterfly Valve?
A: Butterfly valves are installed by inserting the valve between two flanges using bolts or studs and nuts to hold it all together. This type of installation, of course, makes it impossible to disconnect just one side of the piping system from the valve. That benefit is received using the lug style valve.


3. What is the working principle of manual wafer butterfly valve?

 A: A butterfly valve is from a family of valves called quarter-turn valves. In operation, the valve is fully open or closed when the disc is rotated a quarter turn. The "butterfly" is a metal disc mounted on a rod. When the valve is closed, the disc is turned so that it completely blocks off the passageway. When the valve is fully open, the disc is rotated a quarter turn so that it allows an almost unrestricted passage of the fluid. The valve may also be opened incrementally to throttle flow.


Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:So how does the valve turn on?
The handle of the valve is opened along the pipe and perpendicular to the pipe
Q:What does the valve "4" mean?
This is an inch inch size, 4 inches =1/2 = 25.4mm = 12mm
Q:Is the valve clockwise?
The valve clockwise rotation of the handwheel is to close the valve, counter clockwise direction is to open the valve, the number above said valve opening rotating the handwheel clockwise along the colonel, to the above number 0 corresponding pointer is completely closed; in counter clockwise direction, to a maximum of 5 numbers above corresponding pointer, is the valve open to the largest degree.
Q:What's the material of j41h-16p's valve?
Stop valve characteristics:(1) the structure is simpler than the gate valve, and the manufacture and maintenance are more convenient.(2) the sealing surface is not easy to wear and scrape, good sealing, when opening and closing, there is no relative sliding between the valve and the sealing surface of the valve body, so the abrasion and abrasion are not serious, the sealing performance is good, and the service life is long.(3) when opening and closing, the valve stroke is small, so the cut-off valve height is smaller than the gate valve, but the structure length is longer than the gate valve.(4) the opening and closing moment is big and the opening and closing are more strenuous.(5) large fluid resistance, due to the valve in the medium channel is tortuous, large fluid resistance, power consumption.(6) the flow direction of medium nominal pressure PN is less than or equal to 16MPa, commonly used downstream, medium from the valve under the direction of flow; nominal pressure PN = 20MPa, using reflux, medium from the valve on the downstream direction to increase the seal. When used, the cut-off valve medium can only flow in one direction, can not change the direction of flow.(7) when fully open, the disc is always subject to erosion.
Q:How do you calculate the flow of the valve?
Valve flow calculation value is very vague, pipe pressure, back pressure, medium viscosity, medium temperature, valve structure, and so on, will affect the calculated value.
Q:The valve has a clear opening and closing sign. What does this sentence mean?
Simply speaking, a gate valve, hand wheel will be above the arrow and open and close the text, indicating that you are clockwise valve open or counterclockwise valve open, so as not to make mistakes, accidents. Other valves are similar in sense and sign.
Q:What does the valve QF mean?
Valve type, one of the contents, Q refers to the ball valve, F refers to the F-4 seals.
Q:What is the difference between the valve before the pump and the valve after the pump?
Pump front valve: current limit; pump rear valve: limit pressure.Pump operating procedures: the pump must be closed before and after the valve, open the pump, slowly open the pump front valve, pump pressure normal, slowly open the pump, valve until all open. If the pump is in front and rear valves are opened, the pump is very easy to burn the motor.
Q:How big valves are used in the DN90 pipeline?
If you use a 97 tube, the inner diameter of 89- phi 90., nominal pressure is low, then try to use DN80, DN80 valve diameter of 80, you can try butt welding
Q:Valve pressure test
The standard is different, the test is not the same, what kind of valve you, a domestic valve only do stress testing, in fact, the pressure can generally be guaranteed, many are bad at high temperature or life testing above

1. Manufacturer Overview

Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range