Q:What does valve qz45x - 10q mean?

Crown valve pressWhat does Q stand for? I'm not sure. It's probably made of ductile iron"Z" means "gate valve"4 represents flange connection5 represents the dark bar (1 represents the Ming pole)X stands for rubber seal and soft seal10q stands for 10 pressure

Q:Analysis of the advantages of elastic seat sealing gate valve?

General valve on the market for a long time there is Water Leakage or rusting, overcome the valve seal bad, rust and other defects, using the elastic elastic valve seat seal gate produce small quantities of elastic deformation of the compensation function to achieve a good sealing effect, with a switch to lighter and reliable sealing, good elastic memory and life and other significant advantages. The utility model can be widely used as an adjusting and intercepting device for pipelines such as water supply, sewage, building, petroleum, chemical industry, food, medicine, light industry, electric power, ship, metallurgy, energy system, etc.. This is the advantage and advantage of an elastic seat seal gate valve.

Q:What are the advantages and disadvantages of flat gate valves?

The advantage of flat gate valve is that the flow resistance is small, and the flow resistance is similar to the flow resistance of short valve. The flat gate valve with guide hole is installed on the pipeline and can be directly cleaned with the cleaner. As the gate is sliding on the two seat surface, the flat gate valve can be applied to the medium with suspended particles, and the sealing surface of the flat gate valve is actually positioned automatically. The seat seal surface is not subject to thermal deformation of the valve body. Moreover, even if the valve is closed in cold condition, the thermal elongation of the stem will not cause the seal to be subjected to overload. The length of the structure is much shorter than that of the ball valve, and it is easier to start. Light plate gate valve is more refined, but the effect is exactly the same.The disadvantage of flat gate valve is that when the medium pressure is low, the sealing force of the metal sealing surface is insufficient, so as to achieve satisfactory sealing. On the contrary, when the medium pressure is high, if the sealing surface is not lubricated by the system media or foreign media, often opening and closing may cause the sealing surface to wear too much. Another disadvantage is that the circular motion of the circular gate in the circular flow, only when it is at the valve closed position of 50%, this valve is more sensitive to flow control. Moreover, the gate will produce severe vibration when it breaks the high-speed and dense medium flow. The valve seat can also be throttled if the seat is made of a V - shaped opening and is tightly oriented to the gate.

Q:Function of gate valve

The valve (including the valve and valve) is a fluid pipeline control device, its basic function is to connect or cut off the pipeline medium circulation, changing the medium circulation, change the direction of the flow medium, medium pressure and flow regulation, to protect the normal operation of pipeline equipment.

Q:About fire valve is gate valve or butterfly valve problems?

Disease is generally in accordance with the design requirements, regardless of the butterfly or tie hair to meet the requirements, are two-way valve.

Q:What is a protective gate valve? What is gate valve knowledge?

Explosion-proof valve products, is a kind of safety valve can eliminate the shock wave which can stop the water hammer shock wave, it is a product composed of multiple sets of safety,

Q:What does gate valve DN80-PN16-QT450 mean?

DN80 means that the nominal diameter of the gate valve is 80mm, and PN16 is the nominal pressure of the gate valve is 16Mpa. Q quick form T cast iron, 450 flanged connection single gate valve.

Q:Why does the centrifugal pump start and stop in the case of closing the gate valve?

After the valve is closed to stop the cause of centrifugal pump outlet valve is closed to stop the pump to prevent the flow back into the pump, impeller, impeller in reverse, part of the mechanical seal in the pump pump impeller reversal will have adverse consequences, serious damage to the centrifugal pump, to close the valve after the shutdown.

Q:greater than DN50 of the pipeline butterfly valve?

I don't know why it was designed. Provide you with some information you refer to, I do not know if it works for you1, stop valve and gate valve are very expensive, more than DN50 can make a lot of money2, butterfly valve is only more than DN50, no small, there may be, but I almost can not see the market.3, like DN150, DN200 such cut-off valve, gate valve is very large, and the butterfly valve is relatively light, installation can save the cost of the block, the valve itself saves too much money.4, but most of the butterfly valve used for a long time are closed.

Q:What are the differences between the gate valve and the cut-off valve?

3, the valve is used in the system is relatively large, to close the gate off system; and the valve is used in the system is relatively small, and to adjust the flow quantity of the system, can not be closed gate and globe valves of different specifications for a variety of occasions, such as the valve rod the dark bar valve, gate valve, wedge gate valve, single valve, multi valve valve body structure is different, large volume. Generally large and nominal caliber DN50 mostly with gate valve, especially industrial high temperature, high pressure and other occasions.4, the cut-off valve is able to stop and adjust the flow, small footprint, small size, generally less than the nominal diameter, DN50 occasions use it. Two can be closed, in the flow of linear requirements are not high, you can adjust the flow. Just because of its structural characteristics of the valve to make its flow resistance, so there is a demand for throttling with a little more than the gate valve. In addition, the cut-off valve, whether it is a formal or reverse installed, in the opening and closing process, there is always a very difficult, and therefore can not do a great deal, or it is not easy to open and close. In addition, the sealing valve has the characteristics of one-way sealing effect, so that the utility model can prevent the working substance from flowing upstream