Valve with Competitive Price from 50year Old Valve Manufacturer

Ref Price:
Loading Port:
Tianjin
Payment Terms:
TT or LC
Min Order Qty:
100 pc
Supply Capability:
10000 pc/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

 

1.Structure of Gate Valve Description

A gate valve, also known as a sluice valve, is a valve that opens by lifting a round or rectangular gate/wedge out of the path of the fluid. The distinct feature of a gate valve is the sealing surfaces between the gate and seats are planar, so gate valves are often used when a straight-line flow of fluid and minimum restriction is desired. The gate faces can form a wedge shape or they can be parallel. Gate valves are primarily used to permit or prevent the flow of liquids, but typical gate valves shouldn't be used for regulating flow, unless they are specifically designed for that purpose. Because of their ability to cut through liquids, gate valves are often used in the petroleum industry. For extremely thick fluids, a specialty valve often known as a knife valve is used to cut through the liquid. On opening the gate valve, the flow path is enlarged in a highly nonlinear manner with respect to percent of opening. This means that flow rate does not change evenly with stem travel. Also, a partially open gate disk tends to vibrate from the fluid flow. Most of the flow change occurs near shutoff with a relatively high fluid velocity causing disk and seat wear and eventual leakage if used to regulate flow. Typical gate valves are designed to be fully opened or closed.When fully open, the typical gate valve has no obstruction in the flow path, resulting in very low friction loss.

 2. Main Features of the Gate Valve

• Valve body cavity using non-toxic epoxy resin,both inside and outside flashboard completely is coated with rubber

•  Free of water pollution

• High manufacturing accuracy

• High strength

• Environmental protection and energy saving

• Good visual effect

3. Images

 

Valve with Competitive Price from 50year Old Valve Manufacturer

Valve with Competitive Price from 50year Old Valve Manufacturer

4. Gate valve Specification

 Valve with Competitive Price from 50year Old Valve Manufacturer

5.FAQ

1. What's are the characteristics of gate valve?

The distinct feature of a gate valve is the sealing surfaces between the gate and seats are planar, so gate valves are often used when a straight-line flow of fluid and minimum restriction is desired. The gate faces can form a wedge shape or they can be parallel. 

2. What is the work principle of gate valve

 The gate faces can form a wedge shape or they can be parallel. Gate valves are primarily used to permit or prevent the flow of liquids, but typical gate valves shouldn't be used for regulating flow, unless they are specifically designed for that purpose. Because of their ability to cut through liquids, gate valves are often used in the petroleum industry. 

3.  What is the structure?

Bonnets provide leakproof closure for the valve body. Gate valves may have a screw-in, union, or bolted bonnet. Screw-in bonnet is the simplest, offering a durable, pressure-tight seal. Union bonnet is suitable for applications requiring frequent inspection and cleaning. It also gives the body added strength. Bolted bonnet is used for larger valves and higher pressure applications.

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:How to identify a good or bad valve?
First, the appearance, two according to the standard to see flange thickness, outer circle, wall thickness and other dimensions are standard, 3 see details.
Q:How do you see the valve number?
The meaning of valve number:Valve type Z, J, L, Q, D, G, X, H, A, Y and S respectively: gate valve, globe valve, throttle valve, ball valve, butterfly valve, diaphragm valve, plug valve, check valve, safety valve, relief valve, drain valve.The connecting codes for valves are 1, 2, 4, 6, 7, respectively: internal thread, 2, outer thread, 4, flange, 6, welding, 7, pair.Valve transmission mode code 9, 6, 3, respectively, said: 9, electric, 6, pneumatic, 3, turbo worm.Body material Z, K, code Q, T, C, P, R and V respectively: grey cast iron, malleable cast iron, ductile iron, copper and alloy, carbon steel, stainless steel, chrome nickel chromium nickel molybdenum stainless steel, chromium molybdenum vanadium steel.Seat sealing or lining R, T, X code, S, N, F, H, Y, J, M, W respectively: austenitic stainless steel, copper alloy, plastic, rubber, nylon plastics, fluorine plastic, Cr stainless steel, hard alloy, rubber lining, Monel alloy, valve body material.
Q:What is the difference between the valve before the pump and the valve after the pump?
Before the pump few valves, up to a foot valve, pump valves, convenient maintenance, then the most important is that the action of check valve backflow, water hammer....
Q:Proportional valve why than other small pipeline valves
3.10 pipes and their accessoriesGraphical representation of numbers, names, symbols3.10.1 flow pipeline thick lines.3.10.2 meter, pipe line, heating and blowing pipeline, fine solid line3.10.3 pipe with casing3.10.4 steam tracing tube3.10.5 cross pipe means two pipe crossing is not connectedThe 3.10.6 intersecting pipe refers to the intersection of two pipelines, and the diameter of the connecting point is 3~5 times of the line width of the connected pipe line3.10.7 branch pipeline3.10.8 medium flow is generally marked near the valve graphical symbolsThe 3.10.9 heat retaining tube may be represented by the symbol on the local portion of the insulated pipe3.10.10 pipe slope, line slope mark, drawn by the slope symbol in GB4458.43.11 general connection form of pipelineNumber, name, graphic symbol3.11.1 flange connection3.11.2 flow orifice3.11.3 pipe end sealing plate
Q:What's the difference between valves and valves without valves?
In that regard, some valves are one-way valves, only out of the can
Q:How do you calculate the valve wall thickness, pressure, and other valve design calculations in a spreadsheet?
For you to introduce the spreadsheet calculation, application basis, you according to this principle for valve correlation calculation:When A1 and B1 cells are used as parameters, the amount of computation is calculated by C1. If the formula is X+Y=? In the A1 cell, fill in the X; fill the Y in the B1 cell; fill in the C1 cell with "=A1+B1"; enter the carriage, and then calculate the corresponding value in the C1 cell. For example: fill in 5 in the A1 cell; fill in 8 in the B1 cell; enter the carriage, and then appear in the C1 cell 13. Other calculations are the same, you will calculate the valve formula, such as the above fill in, given the corresponding parameters, the same can be calculated.
Q:What valve does the high pressure by-pass valve DN254 * 800 belong to?
This is because the bypass valve is a special valve and other valve type theory.This is custom-made valves, generally no inventory, and may not have the material you need. So it needs to be customized.I remember the German HORA had the valve, but the price was sky high.
Q:The valve is rusty and can not be opened. What shall I do?
Remove the handle and lever the stem rotation with a wrench,
Q:How about leaking water pipe valve?
What specific circumstances, I teach you repair what valve, how big, which seal leaks
Q:What should be checked before using the valve?
5, check valve disc or spool movement is flexible and accurate, no bias, displacement or skew phenomenon6, spring-loaded safety valve should be sealed, positioning lever type safety valve should have the weight of the device7, rubber lining, lining enamel and plastic lined valve body surface should be smooth, the lining layer and the substrate firmly, no crack, blister defects, using high frequency electric spark generator to inspect the lining surface, not found in liner breakdown (white flash phenomenon) is qualified8, the valve flange sealing surface should meet the requirements, and shall not have radial scratches

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range