Silicon Carbide Foam Filter series JG-201 JG-202 JG-203

Ref Price:
Loading Port:
Guangzhou
Payment Terms:
TT OR LC
Min Order Qty:
1 pc
Supply Capability:
10000000 pc/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Ductile, Grey Iron, Vermicular Cast Iron and some Iron Alloy,and also for filtrating non-ferrous alloy, such as Cooper alloy and Aluminum alloy. It can remove impurities efficiently, and make metal filling steady in mould. It can also reduce air flow and casting impact in mould, and decrease pin hole, sand hole defeats to increase casting quality and product rate.


JG-202 Silicon Carbide Foam Filter


 These series of products are newest products, which are produced through special material formula and latest advanced technology. Compared with normal ceramic foam filters, these new series products can be used at a higher temperature, which have higher strength at room temperature and high temperature. The physical property of this special material enables JG-202 series filters to have a better thermal shock resistance. They are suitable for harsh casting condition, such as placing on the bottom of vertical runner and casting at high temperature.


JG-203 Silicon Carbide Foam Filter


This product is produced through special material formula, and it has good durability, high thermal shock resistance and high porosity. It is mainly applied in filtrating heavy castings and medium-large casting, such as windmill, machine tool, ship parts and large part of mechanical equipment, etc.


Parameters


TypeMaterialsCompressive

Strength (Mpa)Porosity (%)Bulk Density

(g/cm3)Applied Temp.(≤℃)

JG-201SiC≥1.280-900.40-0.551500

JG-202≥1.578-900.45-0.601550

JG-203≥2.078-900.45-0.601500


Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Can the plate filter press pass through the filter plate?
Specific, it is necessary to choose the filter characteristics according to different materials. Plate and frame filter press: plate and frame filter press is an industrial realization of solid, liquid separation, plate and frame filter press is suspension, liquid-solid, liquid two phase, applied to chemical, ceramics, oil
Q:What is the reason that the ceramic filter does not absorb mineral powder?
The recoil pressure is regulated by the pump loop valve and the pressure regulating valve. In order to avoid frequent fluctuations in pressure and pressure within a short period of time, a buffer cylinder with a stabilizing effect is provided in the backwash pipe.
Q:The vacuum of ceramic filter is not enough
Maybe the vacuum meter is broken. It doesn't show or show the data is different from the actual data.It could be the source of the vacuum, the vacuum pump failure.Pipeline leakage: vacuum system connecting pipes (metal pipes or rubber pipes) corrosion, aging and water leakage.Distributor head leakage: wear or poor sealing.Leakage of ceramic plate: rupture of ceramic plate.Other reasons.
Q:Why does not the iron filter of the ceramic filter work?
You should make it clear that the filter cake has always been dry or suddenly dry, and now how much moisture? Generally, the ceramic filter is used to filter iron powder, and the water content of the filter cake is about 10%.
Q:What's the reason for high water content in filtration copper concentrate?
Ceramic filter plate1) the service life of the ceramic filter plate has arrived.2), ceramic filter plate uneven in quality on the market, the production capacity of some ceramic products difference (table mask size is too large or pore size uniformity is poor as a result of suction effect is poor, short life), but the price is low, but some users in order to reduce the operation cost of ceramic machine, tend to choose low price the ceramic plate, sometimes a ceramic machine ceramic filter plate with several may be different, so do not get the expected effect in normal use.In addition, the concentrator slurry, especially metal slurry, is very powerful on the wear of ceramic filter plate, the mechanical strength and wear resistance of ceramic filter plate requirements (corundum has high mechanical strength, good abrasion resistance, especially suitable for metal slurry dehydration).When selecting ceramic filter boards, these two points should be taken as a reference.
Q:How many degrees does the ceramic filter melt?
Spinel is basically over 1600-1700. It's not too acid proof.There are other materials such as silicon nitride. Ceramics can be more than 1300 degrees in temperature. So the material you are using now is unlikely to melt and melt, and you can change it into one of the top materials. Baidu, this stuff is all over the street.
Q:The vacuum degree of the ceramic filter is normal and the cake water is large
The vacuum degree of the ceramic filter is normal at about -0.08MPa. Under normal circumstances, the water content of the filter cake treated with a ceramic filter is about 10%, and the moisture content of the tail filter cake is about 15%. The water content of the filter cake increases with the increase of water content in the ceramic filter. I analyze the reasons from two aspects.
Q:The ceramic filter plate is broken. What will happen to the vacuum pump?
At this time, take the filtrate (this is not the first water slurry) will pollute the ceramic filter pipe, friction ring, filtrate pump, may damage the vacuum system, remaining in the pipeline in the pulp will recoil pressure under the action of pollution caused by the other ceramic plates, ceramic plates blocked him. Once the ceramic plate is broken (depending on the severity), it will make the vacuum distortion, resulting in ceramic filter suction effect worse or even no suction!
Q:What is the reason that the whole ceramic filter does not attract ore?
After the joint cleaning, 0~2 hours of suction effect may be good, 2~4 may drop slightly, 4 hours later will become worse and worse, or even suck. This case should first check the backwash water pressure (instantaneous maximum pressure should not be less than 0.08MPa) is to meet the requirements, should also advance down (to ensure normal and ultrasonic cleaning combined with nitric acid dosage sufficient) and prolong the cleaning time.
Q:What filter material are placed in the aquarium filter?
Generally let off the filter cotton and ceramic rings, there are biochemical balls, coral bone, stone, activated carbon and so onConditional: filter cotton, ceramic ring, biochemical ball, coral bone, stone, activated carbon

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range