plastic sheet extrusion machine production line , pvc board production line , pvc decoration sheet production line:
PVC/WPC Free Foamed Sheet Production Line
Professional manufacture with more than 10 years experience.
High output , low consumption
plastic sheet extrusion machine production line , pvc board production line , pvc decoration sheet production line
The plastic plate and sheet extrusion line is specially designed for the extrusion of single layer or multi-layer plate and sheef of PC or PMMA. It is also suitable for the sheet extrusion of PE , PP, PS, ABS and other materials.
The international famous components, combined with decades of year’s experience in the plastic machinery industry, make the whole production line more perfect, reliable and steady.
Product Technical Parameters:
Main motor power(KW)
Designed extrusion output(KG/H)
Send a message to us:
Q:Produce 10 square wires with the smallest extruder
If the production of single core line, then 50 machines can also do, but low efficiency, unstable line,.70 or 90 machine idealIf it is a production sheath line, do at least 70 machines, preferably 70 or 90 insulation, and 90/120 as sheath
Q:What is the temperature setting of the extruder and how much is the setting temperature of the head and filter?,
The temperature setting of the extruder is related to the material you manufacture. If the type of plastic is different, the setting temperature is different, and the material of different manufacturers is also slightly different from the temperature setting.
Q:Cable extrusion machine 6.57090 machine model how to see, know the master to say, thank you
Cable extruder type 657090 machine, describes the diameter of the screw, the unit is mm.The greater the number, the greater the equipment, the greater the amount of gumIt is usually marked on the control cabinet of the equipment
Q:Is the extruder the same as the extruder?
A large number of continuous production, such as tube, rod, profile, also can be used for plastic modification and granulation.The scope of the application is different, but the meaning is similar, reference material, China, extruder, trading network
Q:Extrusion blow molding machine, storage or continuous type good?
This is not good or bad, depends on what your product is If the product cycle large volume high capacity is bound to produce a product with storage because of your long,
Q:Extrusion machine operating procedures, specific points, thank you!
6, the speed from low to high, added to the normal speed, is strictly prohibited high-speed car, observe the instrument on the current value and temperature is normal, in case the current is too large, cause the heater to burn.7, when lifting the disk, we should pay attention to the limit of the rise and fall, not too high or too low, when there is an electrical limit, shall not exceed the limit.8 when feeding to the hopper, be careful not to enter the metal, and do not use a screwdriver or a metal bar to poke the plastic into the screw.9 check the dry test machine, should be equipped with rubber insulation plate, otherwise, no driving.10 before driving, should check whether the ground location is good, grounding resistance should be measured regularly, not higher than 4 Europe; equipment whether there is noise and other anomalies, if there is a problem, repair and reuse.
Q:Equipment is the Changzhou sun extrusion machine,
Is that settled? This technology is not available online! No one wants to say free, need technical contact me!
Q:The working principle of an extruder
What is the working principle of an extruder?:Screw with specific shape,Turn in a heated barrel,It will be delivered from the hopperThe plastic is pressed forward, allowing the plastics to be uniformly plasticized (i.e., melted)Through the head and different shapes of the mold, the plastic extrusionA continuous plastic layer of various shapes, extruded on the core and cable.
Q:How to adjust the 65 screw gap in the extruder?
This should be practical learning. The outlet plane of the barrel is about 3 mm in diameter.
Q:Comparison of injection molding machines and Extruders
Considerations for extruder use:1, extrusion machine is running forward, avoid reverse2, avoid fasting operation, must heat engine feeding operation, so that can avoid sticking bar (holding shaft) phenomenon3, the extruder inlet, vent hole is strictly prohibited access to iron and other miscellaneous, so as not to cause accidents, affect production4, safe use of electricity, grounding wire5. When the machine is running, it is forbidden to touch the rotating parts such as the material inlet, the material outlet, the belt, the gear and so on6, before using the machine should be injected with lubricating oil, so as not to cause damage to the machineSince the extruder as one of the three synthetic plastic material since the advent of rapid development.