Soft PVC sealing strip extrusion machine

Ref Price:
Loading Port:
Shanghai
Payment Terms:
TT OR LC
Min Order Qty:
1 set
Supply Capability:
10 set/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Specifications

Soft Pvc sealing strip extrusion machine 
1-Raw material:Soft PVC 
2-Diameter of the screw:65mm

The whole plant are composed of extruder, water cooling tank, hauling machine, double roller and coordinated with different specification of moulds to produce soft PVC sealing strips for aluminum door and windows to instead of the rubber strips.

Complete production line:

1- Automatic material dryer and feeder SLJ-400

2-Extruder

Model:SSJ-65/25

Diameter of screw: φ65mm

Capacity:70-80kgs/h

L:D: 25:1

Material of the screw: 38CrMoALA with nitrogen treatment

HV:>800

Material of the barrel: 38CrMoALA nitrogen treatment

HV:>800

Power of motor:22kw

Inverter: FUJI

Element: TE and OMRON

Material of heater: ceramic heater

Material: Best stainless steel

3-Water cooling tank

Length:4 meters

Material: Stainless steel

Adjustment distance:500mm

Adjustment direction: three-dimensional

4-Hauling machine

Length of clamp:500mm

Width of clamp:120mm

Adjustment distance:500mm

Clamping: By pneumatic

Speed: 0.6-6m/min

Power of motor:1.1kw

Inverter: FUJI

5-Double roller (easy to operate)

6-Air compressor

7-Crusher

8-Moulds

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:How to choose the mould of the cable extruder? Ten
Depending on your specific specifications, if XLPE is insulated, extrusion die with small touch line, set on the use of cable diameter, large core conductor than a few tenths of good, if you like to use 70 square tube extruding mold insulation of the conductor element some is big 1 can be set according to the touch, the tensile ratio calculation,
Q:Extrusion blow molding machine, storage or continuous type good?
This is not good or bad, depends on what your product is If the product cycle large volume high capacity is bound to produce a product with storage because of your long,
Q:Wire 70 extrusion machine before and after the transfer of the core will change what is the reason?
The nose is not accurate enough or wornOr the screws are not screwed in placeOr die inappropriate, too large
Q:Our factory has a continental 590 control DC motor used in extrusion machine,
You can adjust the proportional gain, and if you don't move, the parameter has this problem, you should check to see if you really lost the pulse
Q:Does anyone know the operating procedures for the cable 65+120 extruder?
What are the operating specifications for the extruder?One is the equipment instructionTwo is the boot operation specificationsThree is safety instructions and so onThe equipment manufacturer will provide the above
Q:Plastic double screw extruder, pumping air will accumulate material, how is it going on?
Adjust the assembly and check the exhaust block
Q:What is an extruder?
Coextrusion is divided into two color co extrusion and hard and soft coextrusion.
Q:Floor heating pipe PERT plastic extrusion machine production process,
Pay attention to the ground anchor.It is better to fasten the joint of the equipment itself.
Q:What should be paid attention to in the daily maintenance of the extruder?
Extrusion machine regular maintenance mainly has these aspectsdrive system(1) check the temperature rise of motor and oil tank, whether the bearing is overheated locally, the abnormal noise of motor and gear, oil leakage, radial circle of oil filter and spline shaft, and the contact gap with the end of screw.(2) regularly clean the oil filter and remove the dirt at the bottom of the tank, and lubricate the lubrication points regularly.(3) the new gear box has been filled with gear oil, and new oil will be replaced every 4000 hours after the operation.
Q:Can PC and PP be extruded together with two materials in an extruder?
No co extrusion, PC polycarbonate, PP polypropylene, two kinds of product structure is not the same, not the same chemical composition, viscosity and liquidity is not the same, processing temperature and processing technology is also very different, and two kinds of products, so not incompatible, CO extrusion.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range