Single Screw Extruder Plastic Machine for Board
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 set
- Supply Capability:
- 10 set/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Single Screw Extruder Plastic Machine for Board
Description of High Quality Extruder
Single Screw Extruder for PVC/ABS/PCFilm Granulating Lineis mainly used to process PP, PE, PPR,ABS and other plastics. Equipped with auxiliary machines, it can manufacture profile, pipes, sheets and other plastic products and granulation. This Single Screw Extruder has the advantage of simple production technological process, high output, stable quality and low cost.
Advantages of High Quality Extruder
1.Suitable for various polyolefin materials: PVC, PC,and ABS etc. single screw extruder adopts advanced human-machine interface control system to realize the automatic control of the whole line
2.Excellent temperature control system to ensure the stability of the producing process. Integrated design of force water cooling and force feeding groove ensures the evenness and stability of the manufacturing process.
3.High-performance driving system; Wearable and easy to maintain.
Technical Parameters of Sigle Screw Extruder
Model | L/D | Output (kg/h) | Speed of Screw Rotation (r/min) | Power (kw) | Center Height (mm) |
JWS45 | 25/28 | 25/30/38 | 10-100 | 11/15/18.5 | 45 |
JWS65 | 25/28 | 50/60/80 | 10-100 | 18.5/22/30 | 65 |
JWS75 | 25/28 | 80 | 10-100 | 37 | 75 |
JWS80 | 28/30 | 100 | 10-90 | 37 | 80 |
JWS90 | 28/30 | 120 | 10-90 | 45 | 90 |
JWS120 | 28/30 | 250 | 10-90 | 75 | 120 |
- Q:Cable extrusion machine 6.57090 machine model how to see, know the master to say, thank you
- Cable extruder type 657090 machine, describes the diameter of the screw, the unit is mm.The greater the number, the greater the equipment, the greater the amount of gumIt is usually marked on the control cabinet of the equipment
- Q:Extrusion machine operating procedures, specific points, thank you!
- 1, operators must be familiar with the procedures, the safety test qualified, wear good protective equipment, shall operate the equipment.2 when the power is on, check whether the thermal control of the electric appliance is sensitive and reliable, whether the thermocouple indicates the temperature is correct or not, and if there is a problem, please repair the personnel to exclude them.3 when driving, should check the main reducer, traction non polar transmission, the line is stepless gear box lubrication is normal, fan ventilation is good.4 before driving, pay attention to the heating temperature of each section, whether the actual temperature required by the process, the heat preservation time should be enough, and the initial heating time can not be less than 3 hours heat preservation.5, not in the plastic bad, scorched, aging, extrusion production, in case of accidents, and found the above problems, immediately try to rule out.
- Q:Where is the Huangyan extruder machine?
- You want to see what type of mold processing, but Masino comprehensive, injection mold, blow mold, mold and so on can be developed.
- Q:Can PC and PP be extruded together with two materials in an extruder?
- No co extrusion, PC polycarbonate, PP polypropylene, two kinds of product structure is not the same, not the same chemical composition, viscosity and liquidity is not the same, processing temperature and processing technology is also very different, and two kinds of products, so not incompatible, CO extrusion.
- Q:What is the waste gas produced by the extruder, granulator and mixer?
- Plastic is a chemical product, and the waste gas produced by the process is organic waste gas. The commonly used and relatively efficient treatment method is activated carbon adsorption. The specific work process is as follows: exhaust gas, air pipe, dry filter, activated carbon adsorption, fan and discharge
- Q:Wire and cable extrusion machine temperature exceeds the process documentation, what are the reasons?
- When making documents, they are not in accordance with the actual situation.
- Q:Why do screw extruders often extrude light red plastic products?
- You should have before the production of red raw material hopper or hopper and barrel, or between the screw shank and barrel etc. the raw material residue, not clean, often with extrusion part.
- Q:How many roots are produced in an hour for an PVC tube extruder?
- It depends on the type of your extruder and the specification of the tube you produced
- Q:Comparison of injection molding machines and Extruders
- Considerations for extruder use:1, extrusion machine is running forward, avoid reverse2, avoid fasting operation, must heat engine feeding operation, so that can avoid sticking bar (holding shaft) phenomenon3, the extruder inlet, vent hole is strictly prohibited access to iron and other miscellaneous, so as not to cause accidents, affect production4, safe use of electricity, grounding wire5. When the machine is running, it is forbidden to touch the rotating parts such as the material inlet, the material outlet, the belt, the gear and so on6, before using the machine should be injected with lubricating oil, so as not to cause damage to the machineSince the extruder as one of the three synthetic plastic material since the advent of rapid development.
- Q:There is a 90 extrusion machine, used in the production of communication cables (outside the cable core is extruded with a layer of LLDPE), now is the configuration of Y2-280M-490KW167A inverter type ACS510197A + ABB), General Motors now found low speed when the current is too large, what reason? How to solve? The details are as follows: used for communication cable production HYA30*2*0.4, 1, line speed is 50 m / min, inverter display frequency 35.3HZ current: 116A; 2, line speed is 40 m / min, inverter display frequency of 28.2hz, current: 140A3, line speed is 35 m / min, the frequency converter significantly method: 157A 24.6HZ frequency current, because the product variety and technical reasons, we need to be in the frequency of 10HZ production. Now, it seems that if I reduce the speed again, the current will probably exceed the rated current. What should I do? Is the motor changed to frequency conversion motor? Or inverter? How to solve? Please heroes pointing, thank you!
- Fan, water pump at low speed, torque is not enough, resulting in high current, if vector control can be ideal.
1. Manufacturer Overview |
|
---|---|
Location | |
Year Established | |
Annual Output Value | |
Main Markets | |
Company Certifications |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | |
No.of Employees in Trade Department | |
Language Spoken: | |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
Single Screw Extruder Plastic Machine for Board
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 set
- Supply Capability:
- 10 set/month
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Related keywords