LED T5 Tube 0.9m SMD Chip High Efficiency 12W

Ref Price:
$7.26 / pc
Loading Port:
Shenzhen
Payment Terms:
TT
Min Order Qty:
10 Pcs pc
Supply Capability:
100000 Pcs Per Month pc/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

LED T5 Tube 0.9m SMD Chip High Efficiency 12W 1. This product meets the standard of CE certification.
2. With internal No-isolated power supply.
3. Round and the elliptical tube are available.
4. Use the most mature international well-known LEDSMD2841 as the light source, which can ensure the led tub35 as the light source, which can ensure the led tube brightness and long lifetime, also can reduce the light decay.
5. Use the high quality aluminum PCB for LED’s better heat dissipation.
6. High-grade PC cover with nice light transmittance(> 95%),Transparent PC cover and frosted PC cover are available.
7. 180 degrees beam angle makes the lighting effect better.
8. CRI(standard products)>70,it can be over 80 if required.
9. Ambient temperature:-20°C-40°C, surface temperature: 42°C-45°C
10. No mercury, lead or other hazardous materials; no radiation, no electromagnetic radiation, no frequency flash, instant start up, no hurting eyes.
Applications:
Replacement for conventional fluorescent tubes:
1. Hotels
2. Conference/ meeting room
3. Commercial Complexes
4. Residential/ Institution Buildings
5. Schools, colleges & Universities
6. Hospitals General li

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:If the body is accidentally broken, will it be electrocuted?
No, only a small amount of fluorescent powder and gas will be slightly contaminated with the environment
Q:Can compatible inductance ballast, electronic ballast led fluorescent lamp tube which have to sell?
I have been able to apply for a patent on the power of led fluorescent lamp which can be compatible with inductive ballast, electronic ballast and direct ac. The loss power of electronic ballast or inductor is about 1W (15W output power).
Q:How do LED lamp tube install how connection?
1: leds are built in, so you don't have to install them directly. 2: the LED tube is an external power source, and the original (electronic or iron core) ballast is removed and replaced by an LED power supply that can be attached to the LED lamp. 3: you also need to pay attention to the LED lamp is double side into electricity or single-ended into electricity, double side into power two ends electricity across the electrodes (note) single-ended into electricity is a head into the electricity but also need to pay attention to is the cathode
Q:Homemade studio, what's the light? What light tube, cold light, warm light
Homemade studio, the proposal USES small volume, energy conservation and environmental protection of the LED lamp, T5 and T8 is right choice, but it is best to choose the warm light, so that better color rendering.
Q:If the led lamp is replaced, the lamp power should be small
B: yes, half of it. 20w is much brighter than before.Yeah, how else to say energy efficiency.I hope my answer will work for you.
Q:What is the connection of the LEDT5 lamp tube, the main line is how to connect, only to the end
Yellow lines don't have to be yellow to be ground.I hope my answer is useful to you.
Q:What's the difference between a single input and a double-end input?
Like our products, single side used on special occasions, be flat installation place, double side is directly used in the traditional ordinary lamp, so change the LED fluorescent lamp is very convenient.
Q:What is the flux of the general led daylight light
See how many wattage, generally 16 w LED fluorescent lamp at present is 1400 lm, luminous flux or new 40 w fluorescent lamp luminous flux highs, but according to the high degree is the LED fluorescent lamp, fluorescent lamp, 360 °, reflective part by stent, the light loss is very big, the LED fluorescent lamp light Angle generally around 170 °.
Q:How does the T8LED light tube replace the fluorescent lamp tube
Step 1: use a screwdriver and a pliers to disconnect the ballast from the wire. But my home is the sun lamp base of zhengtai, the quality is too good, it took 10 years. I didn't even get down to the ballast, which was stuck in a full thick iron base, so I disconnected the wire. The wire that disconnects from the ballast is sure to have two heads, just to disconnect the connection. There is a lot of direct skewers of black tape, some of which use that connector and screw the two wires together. It's the same thing. This is the connector that is used in this case. Disconnect the regenerator, remove the wire and then rewire the two broken wires together and attach the black tape (which is the insulating tape). Put the base back to the original. Install the fluorescent tube, and remember to place the head of the European logo on the base of the current. And when you put it in place, it's going to be OK.
Q:Is it healthy to hang a towel with a bad fluorescent lamp
Mercury vapor reaches 0.04 to 3 mg, which causes chronic toxicity in two to three months. An increase of 1.2 to 8.5 mg can cause acute mercury poisoning, and if it reaches 20 mg, it leads to death.
We are a leading manufacturer of a broad range of LED strip light and LED Tube light. From 2011, we have integrating sphere spectrometer, high speed automatic placement machine, reflow soldering machine, automatic dispensing machines and other specialized equipment and professional R & D department. LED strip light can produce up to 300000 meters per month.

1. Manufacturer Overview

Location Shenzhen,China
Year Established 2011
Annual Output Value
Main Markets

Mid East;Western Europe
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port Shenzhen
Export Percentage
No.of Employees in Trade Department 20 People
Language Spoken: Chinese
b)Factory Information  
Factory Size: Above 4,000 square meters
No. of Production Lines About 5
Contract Manufacturing OEM Service Offered;Design Service Offered
Product Price Range Cheap