Gear planetary gear OEM hobbing,shaving,grinding for machine factory

Ref Price:
Loading Port:
Payment Terms:
Min Order Qty:
100 set
Supply Capability:
10000 set/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:



Steel,as requirements



Pressure Angle:


Place of Origin:

Zhejiang China (Mainland)

technology of material:


technology of machining:





is acceptable

Packaging & Delivery

Packaging Detail:packed in carton
Delivery Detail:70days


1.produce as drawings
2.material will be as requirements
3.strictly quality control
4.OEM is acceptable

Products information:


1. suitable for many sorts of transmission system, such as agriculture tractor, wind power, truck and other industry zone.

2. material and precision can be as requirements.

3. we have complete gear machining equipments: gear hobbing machine, shaving machine, gear shaper, gear grinding machine, and our own heat treatment center. all of the production procedure are strictly controlled by ourselves, no cooperation procession, so we can sure the final products to meet your requirements.

4.each processing, strictly quality control

5.certificate: ISO9001, ISO/TS16949





Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:How many teeth should the flywheel ring gear of the single speed diesel engine 158D12 teeth of the deceleration starter?
functionAt the power output end of the crankshaft, that is, the transmission and the other side of the work equipment. The main function of the flywheel is to store the energy and inertia of the engine while doing the stroke. The four stroke engine has only one stroke to work, and the energy to absorb, compress, and exhaust the energy stored by the flywheel. The balance is correct. The balance of the engine depends mainly on the balance block on the shaft. The single cylinder machine has a balance shaft.
Q:There is no gear with teeth inside or outside, or it is called a ring
1, this practice early, senior car gear system is a planetary gear series (or planetary gear group) in the form of the time shift, all gears are not engaged in or out of action, but the shift is different with the "brake" to change the speed of the ring gear. Different from your imagination is not outside gear ring gear (or pulley), but different friction ring gear brake.2, your approach is feasible: as follows3, when the solar wheel is braking, the output form is outer gear ring - planetary bracket4, when the outer gear ring for braking, the output form: sun wheel - planetary frame
Q:Is there any dust in the punching ring that affects the abs?
What you say is the 4S shop to shirk responsibility, your car is still in the period of three guarantees. In addition ABS lights, the fault is detected, without a clear definition, as you are. You ABS lights and anti-skid lights, either inductive head is not clean, or the sensor is broken, either the bad contact line.
Q:How does the gear ring match the starter? Is there a method of calculating the work type? Tell me about it. Thank you
The two parameters, the modulus m of the starter gear and the pressure angle alpha, can only be deduced
Q:The starting mode of a vehicle engine, in addition to the engagement of the gear ring of the starter motor and flywheel, causes the crankshaft to start
2) the starting and starting device of the auxiliary gasoline engine is large in volume and complex in structure, so it is only used for the starting of large power diesel engines.
Q:The role of automobile gear ring
Hello, dear! Adjacent stall conversion, we should take different steps of the same principle applies to mobile gear shift, the question is the former joint engagement ring gear and sets the rotational speed requirements, and the latter to engage a gear meshing point line speed requirements, but the speed of analysis is based on the principle of the same.
Q:What is the main reason for the radial runout tolerance of gear ring?
4, workpiece or tool loading card positioning is not good, no longer the correct position theory.Think of these, hope you useful points.
Q:Ask an expert to enlighten flywheel ring gear assembly and assembling method!
Diagnosis and repair methodsIf the flywheel is damaged by more than three teeth at the same time, and it is opposite to the starter tooth, it will cause the two gears to be unable to mesh. In this state, only to turn a crowbar to pry the flywheel angle, and then press the start button to start smoothly. For damaged flywheel teeth, welding repair can generally be used.
Q:How many teeth of the 12 gear starter is suitable for the gear ring?
Starter 12 teeth are 1332d, 1315c, 138C, 140, 141, 1115 and 195 and a single cylinder gear and ring gear with them, usually in a single cylinder diesel engine, according to the installation position selection.
Q:Does the flywheel ring gear and the starting machine affect the vehicle?
Both sides of the gear ring have serious wear or tooth damage, and the repair can be repaired by surfacing when the replacement repair does not meet the requirement.Repair of flywheel working faceThe working surface of the flywheel or groove. The wear depth is more than 0.5mm, should be light grinding or after finishing mill. The thickness of the flywheel shall be no less than the new flywheel thickness 2mm after processing. The wave depth is no more than 0.5mm, allowing the existence of no more than two annular grooves, and deburring shall be eliminated.

1. Manufacturer Overview

Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range