WCB Gate Valve DIN3352 1. Factory pice 2. Short Delivery Time 3. All size
BS5136/5150 Ductile Iron Gate Valve
Main technical parameters
The main characteristics and uses
1. Compact structure, rational design of rigid valve, and channel flow, flow resistance coefficient. 2. Sealing surface using stainless steel and cemented, long service life. 3. The use of flexible graphite packing, sealing reliable, flexible and lightweight. 4. Drive sub-manual, electric, pneumatic, gear transmission, structure type: a flexible wedge gate single rigid wedge and the single-gate modeldouble plate board. 5. Widely used in petrochemical industry, coal-fired power plants such as oil, water, steam pipe on the road for access or cut-off line in the gate dielectric
Send a message to us:
Q:What does "Z45W-10T" mean?What does each letter stand for?
W is the seal material or lining material code, the valve sealing material is the valve body material, the valve sealing surface material code with "W" said, here stands for brass;The 10 is the pressure code, which stands for PN10, which is often called 1.0MPa;
Q:What are the main types of gate valves?
sealing surface configuration can be divided into wedge gate valve and parallel gate valve, wedge gate type valve can be divided into: single gate type, dual gate plate and the flexible gate type; parallel gate valve can be divided into single and dual gate gate plate.
Q:What is the size and length of the DN80 gate valve? 10 kg and 16 kg, respectively?
Valve structure length standards are PN16, short series for 203mm, long series for 280mm, flange size by PN16.
Q:What is the difference between the cut-off valve and gate valve, the general will use the cut-off valve instead of gate valve
Stop valve and gate valveThe working principle is different. The stop valve is an upward stem type, and the handwheel rotates and rises with the stem. Valve is hand wheel rotation, stem upward movement. Flow is not the same, the gate valve requires full open, the cut-off valve is not the same. The gate valve has no inlet and outlet direction requirements, and the cut-off valve has the required inlet and outlet!Gate valve and stop valve are shut-off valve, is the most common two valves.From the exterior, the gate valve is shorter than the cut-off valve, especially the bar valve needs a higher height space. Valve sealing surface has a certain degree of self sealing capacity, its spool depends on the media pressure tight contact with the valve seat sealing surface, to achieve tight leakage. Wedge gate valve spool angle is generally 3~6 degrees, when forced to shut down excessive or temperature changes of the valve core is easy to die. Therefore, high temperature and high pressure wedge gate valve, in the structure have taken certain measures to prevent spool stuck. The valve in the opening and closing valve and valve seat sealing surface contact and mutual friction is always so easy to wear sealing surface, especially in close off the valve, the valve before and after the great pressure, sealing surface wear is more serious.
Q:Gate valve, butterfly valve, ball valve advantages and disadvantages? What are the usual valves?
Stop valve: a valve that closes the valve and moves along the center line of the valve seat. According to this form of valve movement, the valve seat opening change is proportional to the valve stroke. Because of the valve stem to open or close the trip is relatively short, but very reliable cut off function, and because changes in the valve seat and the valve stroke is proportional, is very suitable for flow regulation. Therefore, this type of valve is very cooperative for cutting or regulating and throttling.Advantages: in the process of opening and closing, because the friction between the valve and the sealing surface of the valve body is smaller than that of the gate valve, the utility model has the advantages of wear resistance. Second, the opening height is generally only 1/4 of the seat channel; therefore, it is much smaller than the gate valve; usually there is only one sealing surface on the valve body and the disc; therefore, the manufacturing process is better and the service is easy to maintain. Because its packing is generally a mixture of asbestos and graphite, it has a higher temperature resistance. Steam valves are normally used with stop valves.Disadvantages: as a result of the medium through the valve flow direction has changed, so the minimum flow resistance valve is higher than most other types of valves; second, due to longer travel, opening slower than the ball.
Q:What is the allowable leakage rate of the gate valve D?
In GB/T 13927, the leakage rate of the valve is divided into 10 grades, namely: A, AA, B, C, CC, D, E, EE, F, G class. And stipulates that when the order contract does not specify, the metal sealing valve according to D requirements.
Q:What kind of valve is gate valve? Is it different from the cut-off valve?
Gate valve and the role of the cut-off valve, are playing a role in isolation. The difference is that the gate valve and the cut-off valve are constructed differently. Fluid from the gate valve flow and flow direction is straight, there is no change in direction, but in the cut-off valve is from the bottom of the valve flow into the flow from the upper part of the spool.
Q:Gate valve DN65 what does that mean?
Nominal diameter 65 gate valve.This depends on the material of your valve, it is new material, it is to use the outer diameter to do the standard, specifications with 63.75, and so on, because the new material is welded or coated with glue connection. So use the outside diameter as the standard, or the gap will appear.There is also the metal standard, according to the nominal diameter, or flange connection flange and skein skein are industry specifications.When it comes to the end, it must be between the pipe and fittings must be connected.
Q:What kind of copper gate valve copper content standards, there are no national standards?
Please refer to: GB/T12225-2005 "general purpose valve, copper alloy casting technical specification" and GB/T 15116-1994 "die casting copper alloy"
Q:What's the meaning of flexible z45x-10q door valve?
Crown valve pressModel Z45X-10QZ refers to gate valve4 finger flange connection5 refers to the dark bar driveX refers to rubber seals10 refers to 10 kg pressureQ refers to the body material, ductile ironFull bore flange soft sealed gate valve