Ductile Iron Fitting With Flange

Ref Price:
Loading Port:
China Main Port
Payment Terms:
TT OR LC
Min Order Qty:
-
Supply Capability:
-

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Specifications

ductile cast iron fitting
1.EN545/ISO2531,DN80-DN2600
2.for water supply
3.elongation above 5%
4.black bitumen paint

 ductile cast iron fitting

1.EN545/ISO2531,DN80-DN2600

2.for water supply

3.elongation above 5%

4.black bitumen paint

Detailed information:

a. length/pc: 5.7m/6m per piece.

b. Wall thickness: K9 is the normative one, we can supply k7,k8, k10, k12 if requested.

c. Outside sprayed with zinc (in accordance with ISO8179, not less than 130 g/m2) and black bitumen paint (with thickness not less than 70 microns), inside with cement mortart lining as per ISO4179.

d. Joint type: the normative joint are Push-on (Tyton-type) joint, we could also supply Mechanical (K-type) joint and flange type if requested.

e. .Minimum order: 1x40’GP.

f. Delivery time: depend on your requirement and your quantity.

g. Payment term: T/T, L/C, or D/P.

h. we could also do the third party inspection at famous organizations such as SGS, BV, etc.


Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:What are the categories of ductile iron pipe fittings?
But even if it is plastic and rotational, between the two in the process and the use of the effect also has the essential difference. Pipe fittings, usually coated with epoxy resin in ductile iron grooved pipe fittings. But this kind of pipe in the process without heat pipe trench because of rotational rotational adhesion as mature, its internal plastic heat pipe trench.
Q:How can the ductile iron pipe be punched?
Ductile iron should be drilled, the key is to see how big holes. If it is a small hole, you can consider using a small drill around 5mm to slowly wear the pipe, and then gradually reaming. If the fight is relatively large hole, may according to the aperture required first hit a circle hole, and then use a small chisel chisel down, slowly put the plate again to be trimmed. When drilling, add a little oil to cool the drill bit.
Q:How can ductile iron pipes be connected to steel tubes?
But pay attention, because ductile iron pipe material is crisp, and the two connecting flange sealing surface is best all the plane, in order to prevent the uneven force and damage to cast iron flange.
Q:How can the ductile iron pipe be connected to the PE pipe?
Cast iron pipe and PE pipe is connected with a lot of what is the most secure connection, flange connection (PE flange head + anticorrosive steel flanges + rubber gasket).
Q:Connecting process of ductile iron pipe spigot and socket rubber ring
Rubber seal ring is formed by one or several parts of the cover, fixed in a ring or a washer bearing and another ring or gasket contact or the formation of the labyrinth of narrow gap, to prevent leakage of lubricating oil and foreign matter.
Q:How many kinds of elbow of ductile iron pipe?
Speaking from the elbow interface double disc, three double socket, socketEach interface elbow from speaking with 90 camber 45 22.5 11.25 four anglesSo a total of 3*4 =12 elbow
Q:How much is the installation of a two degree elbow for ductile iron pipe fittings at 11.25 degrees?
The main components of ductile iron pipes are carbon, silicon, manganese, sulfur, phosphorus and magnesium. In the ferrite and pearlite matrix on the distribution of a certain number of spheroidal graphite, according to the nominal diameter and the elongation of different microstructure of ferrite and pearlite in different proportions of small caliber pearlite percentage is generally not more than 20%, large diameter of the general control in about 25%. Minimum tensile strength: 420/Mpa, minimum yield strength 300/Mpa, minimum elongation 7%.
Q:Is the cast iron tube the same as the ductile iron pipe?
According to its manufacturing methods can be divided into: sand, centrifugal pipe, straight pipe, continuous cast iron pipe and sand pipe.According to the material used, it can be divided into gray iron pipe, nodular cast iron pipe and high silicon iron pipe.
Q:Is the ductile iron pipe metal pipe?
Ferrous, manganese, chromium, or a substance with a metallic property based on them is called ferrous metal. Ferrous metals are carbon steel, alloy steel, cast iron, etc.
Q:How to inspect ductile iron pipe fittings?
On the quality of single pipe can analyze it from the surface is sand type and water cooled pipes, K8 pipe is different from Shanxi root nature is that the proportion of grade K9 cement and cast iron pipe and the K8 pipe are different, there is no national standard and non standard, no K8 tube, only is the production plant in order to obtain more profits, the dealer is not up to the national standard K9 grade pipe called K8 grade ductile pipe, K9 pipe cement weighs about 1/5 weight of the pipe, but is played in the role of anti-corrosion,

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range