AWWA C110 ductile iron pipe and fitting

Ref Price:
Loading Port:
China Main Port
Payment Terms:
TT OR LC
Min Order Qty:
-
Supply Capability:
-

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

1. Standards : ISO2531, ISO4422, EN545 , EN598 , BS4772 , AWWA C110

2. material : GGG500-7 or other Ductile iron .

3. coating : Fusion bonded epoxy coating ; cement lining inside and zinc primer and bitumen painting outside ; bitumen painting inside and outside ; red anti-rust coating .

4. package : wooden cases with plastic layer , wooden pallets with plastic layer , steel crates .

5. accessories such as gaskets , bolts and nuts available upon request .


Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:How can the ductile iron pipe be punched?
Ductile iron should be drilled, the key is to see how big holes. If it is a small hole, you can consider using a small drill around 5mm to slowly wear the pipe, and then gradually reaming. If the fight is relatively large hole, may according to the aperture required first hit a circle hole, and then use a small chisel chisel down, slowly put the plate again to be trimmed. When drilling, add a little oil to cool the drill bit.
Q:How many kinds of elbow of ductile iron pipe?
You can measure the big money to camber, can call to the manufacturers to build. Seems to have 12.5 and 22.5 degrees, in the first two months we used 22.5 degrees elbow, the drawback is not good pull
Q:Is the ductile iron pipe metal pipe?
Ductile iron pipes are metal tubes, because ductile iron is also a kind of metal. See the classification of metalsGenerally, metal materials are classified into two major categories: ferrous and non-ferrous metals
Q:Could you tell me how to weld ductile iron parts and steel tubes?
MG289 electrode can be selected, welding electrodes and ductile iron into eighty degrees around the pipe around OK, and the intensity is higher than the strength of the cast iron. Direct cold, no heat treatment after welding.
Q:How is the weight of nodular cast iron pipe calculated?
The use of cast iron by adding more than 18 nodularizer, after centrifugal ductile cast iron machine high speed centrifugal cast pipe, called "ductile" (Ductile Cast Iron Pipes), referred to as ball pipe, ductile iron pipe and ductile iron pipe etc.. The utility model is mainly used for conveying water, and is an ideal choice for tap water pipes.
Q:Connecting process of ductile iron pipe spigot and socket rubber ring
Rubber seal ring is formed by one or several parts of the cover, fixed in a ring or a washer bearing and another ring or gasket contact or the formation of the labyrinth of narrow gap, to prevent leakage of lubricating oil and foreign matter.
Q:How can ductile iron pipes be connected to steel tubes?
Disk or disk plug connection, it is best to use flange connection.
Q:Comparison of C and K grades of ductile iron pipes
The nominal pressure ratio of the C class pipe is lower than that of the K grade tube, and the applied pressure is low.
Q:What are the categories of ductile iron pipe fittings?
But even if it is plastic and rotational, between the two in the process and the use of the effect also has the essential difference. Pipe fittings, usually coated with epoxy resin in ductile iron grooved pipe fittings. But this kind of pipe in the process without heat pipe trench because of rotational rotational adhesion as mature, its internal plastic heat pipe trench.
Q:How to improve the quality of nodular cast iron pipe fittings
For cast iron pipe chute taphole bent or improper chute taphole distance socket distance, easy to form a skin defect in cast iron pipe socket parts, equipment manufacturing inspection of cast iron pipe fittings must be in production, replacing the cast iron pipe chute taphole elbow when necessary, and adjust the host making iron centrifuge when the pipe in the lower limit, shorten the chute taphole socket from the distance.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range