Mobile Aluminium platform serie 2

Ref Price:
Loading Port:
China Main Port
Payment Terms:
Min Order Qty:
Supply Capability:

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:What can be done when the hydraulic platform is down?
The left and right sides are connected by wire rope, while the other side is synchronized.
Q:How to use the elevator to be safer and more efficient
Constantly check the operation of the various agencies is normal, have no noise, if find fault, the elevator must be eliminated in time. 2, check the connection of the ministries, such as loose should be tight. When the compression of the connecting bolts should be in body check firmness, slightly shaft must have a split pin all connections, and to open fully. Always check all electrical wires and cables for damage. Make sure to cover and replace damaged parts in time. When the motor is overheat, stop the engine in time, and then keep running after the failure. The motor bearing lubrication is good.
Q:What is the main shaft of the horizontal milling machine
A kind of widely used machine tools, can be processed on milling machine plane (horizontal, vertical plane) and groove (key, T slot, dovetail groove, etc.), tooth parts (gear, spline shaft, wheel lovely, spiral surface (screw, screw groove), and various surface. In addition, can also be used for the surface of solid of revolution, inner hole machining and cutting work. Milling machine at work, workpiece loading on the worktable or dividing the first attachment, cutter rotating movement, accompanied by a table or milling head feed movement, the workpiece can obtain the required processing surface. Because the cutter is intermittent, and high productivity of milling machine
Q:There are several reasons for the hydraulic cylinder oil leak on the elevator
Internal leakage 1) wear-resisting ring on the piston is badly worn, causing friction between the piston and the cylinder liner, and finally pulling the casing, piston and seal. Sealing long term failure, piston seal (mostly U, V, Y ring, etc.) aging; 3) the hydraulic oil is dirty, and a large amount of impurities enter the cylinder to seal the piston seal to the bad.
Q:The home is decorated, make a tatami mat the platform should pay attention to what aspect?
The advantage of pure electric type is that it can be easily and easily accessible by electric or remote control. When the drawback is power failure, the tatami mat can't be used. Manual electric integration tatami lifting table, set the advantages of the above two kinds of control mode, and avoid their disadvantages, so it is a mainstream product. Optimization!
Q:Does the shear fork lift stand belong to special equipment?
In the light of the special equipment safety supervision regulations, hoisting machinery definition: refers to used for vertical lifting or vertical and horizontal moving heavy mechanical and electrical equipment, its range is rated lifting weight greater than or equal to 0.5 t lift.
Q:How does hydraulic platform change sealing ring, how to operate
Flange join type, should remove flange join screw first, use the screw to remove the end of the cover, can not lever or hammer, lest damage; Inside the card key type connection, should use a special tool, the guide sleeve toward the push, reveal the card key and hydraulic plunger pump used to () after remove the card key items with nylon or rubber texture the card key fill out again after its; Thread connection type oil cylinder, should screw the screw down first; In the demolition of the piston rod and the piston, not hard to pull out of the cylinder, piston rod components should try to keep the components of the piston rod and cylinder axis slowly pulled in a line.
Q:What kinds of tables are there? Which is better for the office?
Hand. This is a waste of time and noise. 2: electric. Electric lift, mute. The downside is that you need to replace the whole table. 3: lifting platform. This is a table that is on the table, which is placed directly on the table and does not need to be installed.
Q:What are the elevating institutions
The elevator is also called the elevating platform, which is a lifting device that lifts a person or cargo to a certain height. In the factory, the automatic warehouse logistics system such as vertical transportation, lifting platforms often also equipped with all kinds of plane conveyor equipment, as different height of conveyor line connection device.
Q:How does the table in the middle of the tatami mat go up and down
Need to buy the metal platform of suitable height, use screw to install small table board. Steps are as follows: Installation: desktop lock desktop board with screws on the top of the lifting platform (such as manual lifting platform should be first in the middle of the desktop is boring, the size of the hole to match the rocker tank size).

1. Manufacturer Overview

Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range