knife seat,F-KB051 rubber wood magnetic knife seat
- Loading Port:
- Guangzhou
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1000 pc
- Supply Capability:
- 100000 pc/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
MEAS:25*22*2.2cm
Key Specifications/Special Features:
Size can be customized
Can print your design of packing
Various styles for choice
Can print your design of packing
Small quantity order is accepted
We also have bamboo and plastic cutting board for choice
Our advantages:
All of our products are made by our experienced team of hard working artisans in a safe and responsible environment.
We take great pride not only in the outstanding quality of our products but also in the environment in which they are made
Every product that bears our name was made in an ethically and socially responsible way
Treated by high temperature, making our product antibacterial
Easy to clean, much durable and harder than other board due to the good material
Primary Competitive Advantages:
Brand-name Parts Country of Origin
Distributorships Offered Experienced Staff
Form A Green Product
Guarantee/Warranty International Approvals
Packaging Price
Product Features Product Performance
Prompt Delivery
- Q:How to return to the ordinary lathe tool
- This problem is due to the positioning of the positioning pin hole under the knife body broken and small pallet wear caused by knife positioning, it must be replaced to accurate positioning pin and a positioning sleeve.
- Q:Where are the Holzer elements in the CNC turret?
- Holzer components in the tool holder is called a disk. I have a detailed look at the space
- Q:Numerical control lathe tool holder does not match the system cutter number
- Is not the cover of the knife on the wrong side of the knife on the lid off
- Q:The cutting surface of the optical fiber cutter is like this, what's going on?
- Carefully close the cutting knife to see whether the two sides of the rubber gasket is intact. If intact, carefully observe the top blade to contact fiber piece arc area not intact, then the level of direction was much higher than the top blade gasket, with a 1.5mm as a benchmark, try not to go down fine cutting. The time can shake head check guide rail wear, wear, cutting blade to promote instability, how to adjust is good, the general cutter is used in the IKO guide, should not be so easy to wear. Unless cottage.PS is now some cutting knife, fiber clamp is not good to put the bare fiber will be placed when there will be such an end face.This is the way I transferred, upstairs from the next should be better.
- Q:CNC lathe tool holder can not be reset after the knife to do?
- If you are unable to move the carriage to exit a and then try to use it to turn off the power first hand, or if not it may be burned (IF amplifier module in the boot state can rotate with hand screw it must be.). Look for an electrician, do not have to change the words.
- Q:How to save the supermarket roll bag?
- The market has a rolling bag buckle machine, a hand can pull a bag, not a pull on several only, and that the user to pull two times as long as two, on the one hand can reduce the excessive waste of plastic bags and bags of rolling customers pull out of the waste, in general customers put a lot of tear rolling bag home as a garbage bag or a small number of people, you can also do some publicity
- Q:The direction of the tool head and the tool head of the NC lathe
- G41g42 use the judgment of the tool tip is not the same as you this figure to 09 knife point for the center of the rotation of 180 degrees is the rear tool head position input value evaluation standard front and rear is the same as the input value
- Q:Lathe machining slender workpiece should be matched with the knife
- In the process of turning slender shaft, the clamping method of one head and one head is adopted. When the workpiece is clamped by a chuck, an open air coil is sleeved between the clamping claw and the workpiece to reduce the axial joint angle of the workpiece and the clamping claw. The tailstock with elastic top, so when the workpiece by the cutting heat and elongation, thimble axial expansion, with the form of compensation for the work of the pavilions, reduce the workpiece bending
- Q:What is the difference between the KSJ and HV
- Far, the accuracy of the KSJ knife, the quality is much higher than the HV, the price in that bad! But I'm talking about genuine
- Q:How do you know how to install the roller skates?
- Skating shoe body base generally has several fixing holes to make you bolt between the knife holder and the shoe body is no gap and then hand swinging knife without shaking the OK but then skate like Michael u and H HV of the black flag, such as shoes, you don't need to remove what their knife rack not what the problem is often removed but will reduce the life of tool it is a general method of alloy steel on it is invalid so don't worry about bold play is. I wish you good luck
1. Manufacturer Overview |
|
---|---|
Location | |
Year Established | |
Annual Output Value | |
Main Markets | |
Company Certifications |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | |
No.of Employees in Trade Department | |
Language Spoken: | |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
knife seat,F-KB051 rubber wood magnetic knife seat
- Loading Port:
- Guangzhou
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1000 pc
- Supply Capability:
- 100000 pc/month
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Related keywords