knife seat,F-KB083 Carbonized bamboo knife seat，your best choice
- Ref Price:
-
- Loading Port:
- Guangzhou
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1000 pc
- Supply Capability:
- 100000 pc/month
OKorder Service Pledge
Quality Product, Order Online Tracking, Timely Delivery
OKorder Financial Service
Credit Rating, Credit Services, Credit Purchasing
You Might Also Like
product name：rubber wood knife seat
material：Carbonized bamboo
N.W.：1.286kg
MEAS：22*16.5*15cm
Product advantage：
How does the bamboo product carbonize？Firstly，put the bamboo or bamboo bag into the high-pressure carbonized boiler of 200 degrees - 300 degrees for vapor carbonization.
And after high temperature and high pressure, so that form a hard carbide particles layer on the surface.At the same time,the bamboo itself will be more harder.
The advantage of carbonized bamboo knife seat:after carbonize,hard carbide particles will form a environment not easy living for bacteria on the surface of bamboo product to achieve the antibacterial effect.
At the same time, because after carbonization the bamboo will be more hard than ordinary paper products, preventing wearing and bamboo thorn problem.
Carbonized bamboo knife seat quantity：
Safety, health, bright color，durable，the everyday necessary good products
Anti-mildew change，anti moth
Environmental protection，no crack，no decay
- Q:How to do the slide shoe
- Re tapping, buy 8MM tap (the original nail is 6MM), buy 8mm nail, tapping the time must be vertical, that is, to ensure that the original nail in a line on the good!
- Q:How to return to the ordinary lathe tool
- Remove and check whether the spring pin back position is smooth (with the hands of the press about 20 times). Take a look at whether the end of the spring pin has been seriously worn, the same knife bottom surface is also turned over to see if the limit groove is also serious wear. Wear badly needed to repair or replace.
- Q:CNC machine tool can be drilled hole how to center
- 1, do not need to set the coordinate system (the center), is loaded with a knife, in the process of preparation of processing requirements, reasonable adjust the height and verticality, the proper use of speed and feed rate, the knife tool can be set, simple, can fix a hole.2, if the degree of difficulty and high requirements, please use the circular drilling instructions programming.
- Q:Where are the Holzer elements in the CNC turret?
- A cutter position corresponds to a Holzer element, usually enclosed in a round plastic box
- Q:What is the material of the cutting tool
- Common materials:High speed steel (also known as Feng Steel, Bai Gang): is a kind of tungsten, chromium, vanadium, molybdenum and other high alloy tool steel more elements.Tungsten carbide hard alloy by high hardness and melting point, titanium carbide and cobalt cemented metal made by powder metallurgy method, the hardness and wear resistance are good, hot hardness is very high, so the cutting speed is higher than high speed steel several times or even several times, can not add high-speed steel cutting materials processing the work, but the bending strength and impact toughness of high speed steel much worse than.Ceramic: ceramic powder sintered at high temperature with alumina powder, the hardness, wear resistance and heat resistance are higher than those of cemented carbide.
- Q:CNC turret is also called the sender sensor
- The rotation of the NC turret is positioned by induction.
- Q:Who has any good method or fixture drawings and pictures for younger brother to learn ah, do not be grateful, want to do, but I have not seen this thing, the idea does not come out
- Very simple, find a square on the grinder grinding angle four straight, like a knife, much bit big hole, the drill bit into a wire on the bit in the next attack on the line, but straight shank drill.
- Q:GSK980TA CNC lathe tool holder how to move
- Hand hold tool motor, and then press the knife, I feel that there is no motor movements. 1, if the turret motor does not act, it should be a circuit problem, please check whether or not the work of the holder of the relay, the power supply is not normal, etc.. 2, if there has been support motor action and feeling in the action, that should be a tool of mechanical failure, please rest on the lower left one screw off with six angle wrench tool to see whether the worm shaft can rotate the turret rotation if it will rest to 45 degrees and then try to change the knife, if not to move it please remove the knife. 3, if the knife motor action and click No action, it may be broken or the knife knife signal line transmitting disk bad.Numerical control lathe: in the numerical control machine tool processing part, mainly depends on the processing procedure, it is different with the ordinary machine tool, does not need to make, the replacement many molds, the jig, does not need to adjust the machine frequently. Therefore, the NC machine is suitable for the processing of parts of frequent replacement of the occasion, which is suitable for single and small batch product development and production, and new products, so as to shorten the preparation cycle, save a lot of equipment costs.
- Q:What is a tray roll bag
- The plastic bag used to cover the tray is polyethylene (LDPE)Partial contraction and contractionConventional size is 1 m 2*1 m height is not limited to 2. Then the household garbage bags are collected on the paper tubeIndustrial heat shrinkable tray with a roll bag weight is about 1 kg.
- Q:How do you know how to install the roller skates?
- If you are able to disassemble the wheel of the kind of one-piece knife, the general is divided into 165 holes and the distance between the 195 holes, the general number of roller skates is the distance between the 165 holes of the.When installing tool holder is according to personal habits, but most were filled with the knife knife mounted on the middle sole. That is, the wheel is about the same length as the shoe. This is more comfortable. Of course, there are special requirements in order to toe and heel action to do better, but also will be installed on the front or back.
1. Manufacturer Overview |
|
|---|---|
| Location | |
| Year Established | |
| Annual Output Value | |
| Main Markets | |
| Company Certifications | |
2. Manufacturer Certificates |
|
|---|---|
| a) Certification Name | |
| Range | |
| Reference | |
| Validity Period | |
3. Manufacturer Capability |
|
|---|---|
| a)Trade Capacity | |
| Nearest Port | |
| Export Percentage | |
| No.of Employees in Trade Department | |
| Language Spoken: | |
| b)Factory Information | |
| Factory Size: | |
| No. of Production Lines | |
| Contract Manufacturing | |
| Product Price Range | |
Send your message to us
knife seat,F-KB083 Carbonized bamboo knife seat，your best choice
- Ref Price:
-
- Loading Port:
- Guangzhou
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1000 pc
- Supply Capability:
- 100000 pc/month
OKorder Service Pledge
Quality Product, Order Online Tracking, Timely Delivery
OKorder Financial Service
Credit Rating, Credit Services, Credit Purchasing
Similar products
New products
Hot products
Related keywords
