knife seat,F-KB028 Rubber wood knife seat，your best choice
- Ref Price:
-
- Loading Port:
- Guangzhou
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1000 pc
- Supply Capability:
- 100000 pc/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
product name：rubber wood knife seat
material：rubber wood
N.W.：1.514kg
MEAS：24*15.5*14cm
Specifications:
Has the quite distinct shape of the mountain wood grain, and the contact surface is a good sense
Excellent toughness, process into various curved according to the needs , full of beauty
Solid texture，manufactured goods with firm structure，prolonged service life
The texture of rubber wood is fine and closely woven，pore full of lots ot padding so it's hard to absorb water and corrode.
Description：
1、The knife seat use material of high quality natural rubber wood and take professional advanced machine equipment and manual binding.
2、The knife seat was refined by material, assembly, polishing, painting and other procedures.
3、The knife holder has the advantages of real materials, excellent workmanship, mouldproof and moth proofing, anti bacteria, wear-resisting etc.
4、Hoteam commerce co.，LTD，is a manufactory specialized in all kinds of wood knife handles，wood seats，chopping boards and other woodworks.
5、Because the knife tool contact with tool wet food for long time, is very easy to breed bacteria, you should ensure that dry and clean and put it in the open air
Primary Competitive Advantages:
Brand-name Parts Country of Origin
Distributorships Offered Experienced Staff
Form A Green Product
Guarantee/Warranty International Approvals
Packaging Price
Product Features Product Performance
Prompt Delivery
- Q: To the signal line where the pull resistance, pull resistance to do with the trouble to say clearly?
- In a word: your signal circuit IC no internal resistance, protection. Pull the signal is determined by a high resistance resistor at the high level, while the resistance from the current limit, pull the same. Pull on the device is the injection current, the output current is down; just pull the weak and strong resistance, no strict distinction between what; for non (collector or drain) open circuit output circuit (such as gates) current and voltage capacity improvement is limited, the pull-up resistor is the main function of open circuit output type of circuit output current for the collector channel. All the pull-down resistor pull-up resistor is used in logic circuit, the circuit current is very small, the logic circuit of MOS tube bias current is microampere, even pA uA, the current level to provide a desired level, such as the current level without any output, because there is a pullup resistor so after a level is actually connected to a high level. Power amplifier circuit with no pull down resistor. Pull the signal is determined by a high resistance resistor at the high level, while the resistance from the current limit, pull the same. The pull-up resistor is the main function of the open circuit output current output channel for the collector; main function is connected with the pull-down resistor resistor together to line in the closed circuit driver (node) to a fixed level. Pull on the device is the injection current, the output current is down to note is that the pull-up resistance caused by too large delay output level, including the choice of the principle of resistance: 1, from the current irrigation ability to save the power consumption and chip considerations should be large enough; resistance...
- Q: How can we remove the NC turret
- The first part of the rotation, two screws in the middle of the release, and then lock the 12 release of the knife rest, remember there are still under the four, in the middle of the road there is a flexible adjustment of the long screws
- Q: Why is the number 980 CNC lathe turret always turn and then alarm
- There are several reasons:1: Holzer component line failure.2: magnetic steel and Holzer yuan collision.3: Holzer component short circuit.4: turret motor three-phase inversion or phase.5: Holzer components and magnetic steel dislocation. Fifth faults appear more. Not really put the Holzer component for the. Also look at the turret controller is not a fault.
- Q: How to do the slide shoe
- Knife slide wire can only change the knife holder, if it is wearing a nail sliding wire, you can use the electric drill to wear the nail, remove the nail, replace it.
- Q: How to maintain the lathe tool holder
- If the positioning and clamping action is normal, the push rod 11 is in contact with the corresponding contact 12, and the signal is sent to indicate that the tool changing process has ended, and the cutting process can be carried out.In addition to the positioning of the hydraulic cylinder and the positioning pin, the motor can also be used to drive the clutch to locate, as well as other indexing and positioning mechanisms.
- Q: Tool holder S solution
- The bearing force is even and strong, the center of gravity of the s frame is low, the stability of the slide is stable
- Q: What is the tool rest
- Device for processing long shaft on horizontal lathe.
- Q: What is the difference between numerical control tool holder and power tool holder
- CNC turret is a large class, which includes an ordinary tool holder and power. The common tool holder can only be installed with a fixed knife seat for processing, the power tool holder can be installed with a fixed knife seat, and a power knife holder can be installed.
- Q: 4 station tool structure is the best. The detailed process of mechanical transmission, their demolition a few times, the worm brake to lift the knife. There is a problem in the rise of the knife in the process of the top cap of the spring to the top of the iron cover dead, the result of the death of the knife holder, can not drive. I estimate that the top cap and the angle and the first bevel on the iron cover are not consistent due to wear and tear. For I a person's opinion, hope you enlighten me
- 4 position tool holder structure of numerical control vehicle:Under normal circumstances can be fitted with 4 knives, the knife holder inside a worm with a turbineThe knife and the base on the contact surface of one end gear and two limiting block, the upper surface of the base two end face gear engaged normally a motor and worm shaft.The principle of 4 station tool holder for NC lathe:The knife is receiving the instructions in the form of pulse waves, when receiving a tool change instruction motor drives the turbine and worm. The worm to rotate the cutter knife up end gear separation, when the turret is elevated to a certain extent, together with the turret turret rotation worm together, rotate 90 degrees after encountering a limit block, because the motor power is blocked to when starting to reverse, the natural turret decline on the base end gear limit block lock, complete tool change
- Q: The first reason is that the cutter shaft of the motor shaft is broken for a shaft / how long it will not be able to die!
- This problem is very simple, is not the command input, motor rotation, and the knife is like a rotation and stuck? This is just a tool conversion timeout, unscrew cap above the turret, turret removed, which has four pins, take out to see if bent, or flash, with the change of the pin, the pin can be used for standard parts can be, can not find it on 4mm head cut tail can be loaded
Send your message to us
knife seat,F-KB028 Rubber wood knife seat，your best choice
- Ref Price:
-
- Loading Port:
- Guangzhou
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1000 pc
- Supply Capability:
- 100000 pc/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
