Q:How do you distinguish between TPU tape and PVC tape?

Also, TPU is better than PVC, and the price is much higher than PVC

Q:Where are the PVC tape coating machines being made?

Self adhesive (self-adhesive) machine coating machineI. product uses:Mainly used for kraft paper, trademark paper, advertising paper, double-sided tape, PVC, PU, EVA, foam (sponge), beauty paper, non-woven fabrics, fabrics and other raw materials, self-adhesive, self-adhesive, composite.

Q:How to improve the tensile strength of PTFE defatted raw meal

Teflon skimmed raw tape can be used on gas connections.Polytetrafluoroethylene (Polytetrafluoroethylene), abbreviated as Teflon

Q:What's the quota for PE membrane isolation layer?

Specification for polyethylene tape: its thickness * width * length, in fact, determines what thickness of adhesive tape to use. For example: in order to strengthen the level level of corrosion, corrosion thickness of 1.0mm; corrosion level reinforced, corrosion thickness of 1.4mm; according to the lapping mode with internal and external anticorrosive adhesive tape, tape thickness determination. According to the construction mode of adhesive tape winding, determine the width of anticorrosive adhesive tape. Don't use the manual winding tape is too wide, the construction workers when the efforts are not easy to control, it is best not to exceed 150mm wide; manual mechanical winding (with some simple mechanical and visual), but the maximum width is 230mm; the mechanical winding tape width appropriate to relax, but preferably not more than 300mm.

Q:Is the transparent aluminum foil tape the same as the PVC tape?

InequableAluminum foil tape adopts high quality pressure-sensitive adhesive, good adhesion, strong adhesion, anti-aging and other effects! Heat preservation performance is greatly improved

Q:What's the performance of PVC tape?

Good transparency, good adhesion, good electrical insulation and tightness, stable electrical insulation in humid environment and water

Q:What's the difference between an electrostatic tape and an PVC tape?

PVC electrical tape is in soft polyvinyl chloride (PVC) film substrate, manufacture coated rubber pressure sensitive adhesive, has the characteristics of good insulation, flame resistance, voltage resistance, cold resistance, suitable for automotive wiring, wire winding, insulation protection etc..

Q:PVC are the grades of electrical tape classified? How do you identify the grades?

That is, calcium content of PVC films, the lower the level of the membrane is pure, is a film, and then the analogy is B, C film, that was a bit abstract, general identification of words, but also by experience, such as a real film tensile permanent discoloration, discoloration of white C film stretching the film, winter crisp, etc.,

Q:Toilet water pipe seam water seepage, with raw tape tight, can you?

Note: the purpose of fighting waterproof guards is to make the water pipes inside the floor forming waterproof layer, so that water is not in the floor water seepage, so as to avoid other floor water seepage. The second is from upstairs. First check the water pipe and the ground seam is intact, whether there are cracks, cracks in the gap. If the gap is damaged, drying condition, put the loose broken filling materials clean, and then use the kitchen and toilet water spray over the ceramic tile aperture, 20 minutes after drying for the treasure of the joint damage to fill the gap tile.

Q:What specifications do you have for PVC electric tape?

The first is the PVC of type 3. Compared with type 5, the production of type 3 PVC requires long reaction time and high polymerization temperature, and requires high added material. The production cost is 50-100 yuan / ton higher than that of type 5. 3 type PVC high purity, small fish eye, easy to blister, with high temperature resistance, insulation, soft products and other characteristics, mainly for the production of soft products, such as wire and cable, agricultural films, conveyor belts, plastic products for daily use.Again, the SG-7/SG-8 and SG-5 PVC. The three resins are basically the same process and the production unit is the same. The main difference lies in additives, formula, polymerization temperature, reaction pressure and so on.In terms of reaction temperature and reaction pressure. SG-8 resin has basically reached the limit pressure of polymerization reactor, reaction conditions more stringent requirements, the operation, safety, technology, personnel quality and other aspects of the requirements, and it is more difficult to control the quality of resin.