Q:What are the common standards for gate valves?

1, product standardsGeneral purpose valves, flanged connections, iron gate valves, GB/T 12232-2005General requirements for steel valves GB/T 12224-2005"Steel flat gate valves for pipelines" JB/T 5298-91Inspection and test of valves. JB/T 9092-1999Standard for safety evaluation of drinking water distribution equipment and protective materials GB/T 17219-1998

Q:what are their applicable conditions? Advantages and disadvantages?

Butterfly valve is a disc type of open and close parts reciprocating reciprocating about 90 degrees to open, close and adjust the fluid channel of a valve.Advantages: the butterfly valve has the advantages of simple structure, small volume, light weight, material consumption, installation of small size, and torque is small, simple and rapid operation, and also has good flow characteristics of regulation and sealed off, is nearly 10 years the fastest growing valve, high temperature and high pressure, and to large diameter, high sealing function of the direction, long life, good adjusting features and a valve development.Disadvantages: the butterfly valve relative to the gate, ball valve pressure loss is relatively large, it is suitable for pressure loss requirements lax piping system.Under normal circumstances, it is not suitable for high temperature and high pressure pipeline system.Valve is closed parts (valve) moving along the centerline of the valve seat, the valve stem to open or close the trip is relatively short, but very reliable cut off function, and because changes in the valve seat and the valve stroke is proportional to, is also very suitable for the regulation of traffic.Advantages: in the process of opening and closing, the friction between the disc and the valve body is smaller than that of the gate valve, so it is wearableThe opening height is generally only 1/4 of the diameter of the seat channel, so it is much smaller than the gate valveGenerally, there is only one sealing surface on the body and disc, so the manufacturing process is good and easy to maintain;Disadvantages: the flow resistance coefficient is relatively large, resulting in pressure lossUnsuitable for large caliber productionThe opening and closing moment is larger and the structure length is longer.

Q:Installation and operation instructions of knife gate valve

3., check the packing parts require compaction, not only to ensure the sealing of the packing, but also to ensure that the gate open flexible;4., before installing the valve, users must check the valve type, size and attention to the media flow direction, to ensure consistency with the valve requirements;

Q:What is gate well?

Technical requirement:1: the valve itself can not seep, it must ensure its tightness;2: water supply pipeline during use, pipeline will be pressure from different aspects, which will produce different degrees of jitter or settlement, which requires the connection of water supply pipes and valves in the well to be reliable, able to adapt to a certain degree of jitter and settlement, and to prevent water infiltration into the well chamber in the pipeline valve wells; deep, slightly larger are generally made of cast iron valve (such as the cut-off valve, butterfly valve) iron valves long-term immersion in water, will affect the service life or cause fracture, so the sealing requirements are higher;3: valve shaft, shaft and well body, manhole cover way of connection should be reliable, not because of heavy rain or water seepage water into the well room.4: valve well is buried in the ground, to bear from different directions of different pressure, and different chemical substances corrosion and damage, and requirements of its pressure capacity and acid and alkali corrosion is better.

Q:What gate DH10016, AM

The first Z represents the gate valve (the initial consonant of the Chinese phonetic alphabet for the gate); the second 2 represents the drive mode of the valve, that is, electro hydraulic drive.

Q:What are the differences between the gate valve and the cut-off valve?

Is the gate valve opening and closing parts, RAM direction of motion perpendicular to the direction of the fluid, valve can only be fully open and fully closed, is not suitable for regulation and throttle. The gate has two sealing surfaces. The two sealing surfaces of the most commonly used wedge gate valves form a wedge. The wedge angle varies with valve parameters, usually 5o. Wedge gate valve can be made into a whole, called the rigid gate; can also be made to produce micro deformation of ram, in order to improve its process of deviation, make up the sealing surface angle in the process, the gate is called the flexible gate. Valve closed, the sealing surface can only rely on medium pressure to seal, that is to rely on medium pressure to the gate sealing surface pressure to the other side of the seat to ensure the sealing surface seal, which is self sealing. Most of the valve is forced seal, that is, when the valve closes, to rely on external force to force the gate to the seat, in order to ensure the sealing surface sealing.A stop valve is a valve that closes the valve and moves along the center line of the valve seat. According to this form of valve movement, the valve seat opening change is proportional to the valve stroke. Because of the valve stem to open or close the trip is relatively short, but very reliable cut off function, and because changes in the valve seat and the valve stroke is proportional, is very suitable for flow regulation. As a result, this type of valve is ideal for use as a shut-off or regulator and throttling

Q:What does the gate valve SZ45X-1.0 stand for?

Z- stands for gate valves, 4 for flange connections, 5 for wedge wedge single gate, X for rubber seals, and 1.0- for PN1.0MP

Q:What is the difference between a flanged gate valve and a wire gate valve?

This is very simple, flanged gate valve is the valve with both ends of the flange, the installation of the pipe to weld the reverse flange, bolt with the pipe flange and valve flange connection. Valve is the valve ends with wire wire, a wire and wire points, and pipeline installation, connecting part with joint or head of the screw and the valve directly on the pipe screw connection.

Q:The legend of gate valve and stop valve

When the valve is installed, the medium can enter from the bottom of the valve core and enter the two way from the top. Medium from the spool into the advantages of the valve closed when the packing is not under pressure, can extend the service life of the packing, and can be pressure in front of the valve in the case of replacement of packing work. Medium from the spool into the bottom of the shortcomings of the valve driving torque is larger, about 1.05~1.08 times above the entrance, the stem by the axial force of large, easy to bend the stem. To this end, the media from below to enter the way, generally only applicable to small caliber manual stop valve, to the valve closed, the media acting on the spool of force is not greater than 350kg limit. Electric cut-off valve is generally used to enter the media from the top way. The disadvantage of the medium entering from the top is just the opposite of the way it is entered below.Compared with the gate valve, the utility model has the advantages of simple structure, good sealing performance, and convenient manufacture and maintenance. The disadvantage is that the liquid resistance is large, and the opening and closing force is large. Gate and globe valves are fully open closed type valve, cut off or connected as the medium use, not as a control valve.The range of application of stop valves and gate valves is determined by their characteristics. In the smaller passages, the cut-off valve is used when required for better shutoff; in the steam pipe and the large diameter water supply pipe, the gate valve is generally used because of less fluid resistance.

Q:What kind of valve is gate valve? Is it different from the cut-off valve?

Gate valve is applied to the big diameter pipeline valve, the valve is generally used in small pipe diameter pipeline, their internal structure is different, the valve can not regulate the flow of water, the valve can be. If you want to understand in detail, it is recommended to take a sample of valve manufacturers to see the internal structure.