Pulley Stock Aluminum

Hot Products

stainless steel guide pulley for passing steel wire,for sales manufacturer made in china

Steel v-pulleys ,Simplex plate chainwheel Sprockets,X458 Chain and Trolley

GEARS DIN ANSI Large Steel shaft Gear of China Manufacturer

Steel v-pulleys 4TNE94 4TNV98L Engine Parts V-belt pulley

Steel V-pulley wheel timing pulley V-pulley ; Pulleys ; V belt pulleys SPZ,SPA,SPB,SPC

YANMAR diesel Engine spare Parts yanmar genuine parts 4TNE94 129916-21680 v-pulley

Small Stock Bore V-pulleys Variable Speed pulley Variable Speed pulley

Adjadjustable speed v-pulley STEPLESS VARIABLE SPEED PULLEYS

Guide pulley,door hanger roller, steel pulley,rope pulley,v-pulley

V-pulley ; Pulleys ; V belt pulleys SPZ,SPA,SPB,SPC

FAQ

Drive to do a linear movement of the spiral, look at the net efficiency of the ball screw rod is relatively high, if the ball screw to make the counter revolution, is the nut with a one-way bearing vertical fixation, screw up and down reciprocating motion, so that you can do, if possible, wire rod length 40CM screw diameter, 8MM, vertical pressure 80N of the screw, choose the lead big nut can make the speed to 700 RPM in the under pressure?

Many manufacturers are now producing this kind of machine, that is, the rotor and the screw nut are made together

What kind of lubricant does nylon transmission use?

Yes, you are not very high speed. I want to know more about the detailed working conditions there. Do you want to contact me?

The axial force of this drive eliminates the problem of how to do it! Thank you for the exam tomorrow

The axis III is under the action of gear 3, and its force direction is right. In order to counteract the force of the axis III, the worm gear 6 should be anticlockwise! The worm 5 and the rotation of the worm gear 6 also depend on the steering of the axle III.Therefore, to solve this problem, we must first determine the axis I steering, that is, bevel gear 1 steering.

When the coupling is linked, can the drive shaft be thinner than the motor shaft?

More consideration should be given to the load capacity of the transmission shaft (strength, rigidity, mechanical performance), and if the load is small and the shaft length is not long, the transmission shaft can be smaller than the motor shaft.

How to prevent the transmission shaft from breaking and falling off?

The dynamic unbalance of the drive shaft assembly goes beyond the standard specification.Deformation of transmission shaft, balance strip fall off, balance of bearing cap, asymmetry of gasket, etc..Loose or damaged bolt of transmission shaft.The assembly of the drive shaft is not proper and the edge 4 bolts are not tightened according to the specified torque; or a certain screw is slipping and the cross bearing is lack of slidingGrease and improper lubrication etc..

What are the functions of an automobile powertrain? What is the function of each part of it?

Rear drive - RR: rear engine, rear wheel driveThis type of arrangement is adopted on large passenger cars, and a small number of mini and light sedans are also adopted. The rear engine, the front axle is not easy to overload, and can make full use of the trunk area, also can effectively reduce the floor height or the middle of the bus to make full use of the space below the floor luggage, but also conducive to reduce the impact of high temperature and noise of engine drivers. The disadvantage is that the engine cooling conditions are poor, some of the faults in driving are not easily detected by the driver. The long distance operation also makes the control mechanism complex and inconvenient for maintenance and adjustment. But because of its outstanding advantages, it is used more and more in large buses.

What part of the transmission mechanism of the walking conveyor?

Cone gear reducerYK series cone - cylindrical gear reducer for working conditions: ambient temperature -40 ~ 40 degrees; the input shaft speed of not more than 1500r/min, the gear meshing line speed is not greater than 25m/s, the motor starting torque is two times of the rated torque reducer. The characteristic of YK series: using a circular arc bevel gear and the one or two, three gear combination, the bevel gear as high level (four level reducer as level second), in order to reduce the size of the small bevel gear; gear are made of high quality alloy steel carburizing and quenching, refined processing, cylindrical gear accuracy reached GB/T10095 in the 6 stage, the bevel gear precision of GB/T11365 in grade 7;

This problem for a long time, a drive shaft with a key, how to fix the position after the rotation of concrete keyway, don't specify the rotation and rotation angle, through parallel or perpendicular to that location

I've seen other people, can first determine a plane for reference and choose the angle